source: wiki/pages/en/Installation-Recovery-en @ 26941

Last change on this file since 26941 was 26941, checked in by obi, 5 years ago

wiki add de pages

File size: 17.6 KB
Line 
1----
2'''8 Installation and Recovery Contents''' [=#point8] ([wiki:Wiki-en#point0 Contents]) ([WikiStart#point0 Main page])
3----
4
5[[br]]
6
7This section contains information on instalation and removal of TitanNit from your receiver
8
9[[br]]
10
11 * [#point8.1 8.1 Atemio510 and compatible Models]
12 * [#point8.2 8.2 Atemio520 and compatible Models]
13 * [#point8.3 8.3 Atemio530 and compatible Models]
14 * [#point8.4 8.4 Atemio7600 and compatible Models]
15 * [#point8.5 8.5 Atemio700 and compatible Models]
16 * [#point8.6 8.6 Atemio7000 and compatible Models]
17 * [#point8.7 8.7 Ufs910]
18 * [#point8.8 8.8 Ufs912]
19 * [#point8.9 8.9 Ufs922]
20 * [#point8.10 8.10 Installation on other Fortis Receivers]
21 * [#point8.11 8.11 Uninstallation On other Fortis Recievers]
22
23
24[[br]]
25
26
27----
28'''8.1 Atemio510''' [=#point8.1] ([wiki:Wiki-en#point0 Contents]) ([WikiStart#point0 Main page])
29----
30
31[[br]]
32
33'' How do I install an Atemio 510 IRD image? ''
34 * Visit the Atemio homepage or the AAF digital forum and download the latest firmware TitanNit .
35 * Extract the zip file
36 * Now copy the unzipped IRD firmware file to a formatted FAT32 USB stick.
37     Note: The USB stick should not be formatted with windows. Use a separate program, such as the
38     " HP USB Disk Storage Format Tool" (freeware program).
39     Furthermore, we recommend a cheap USB stick with a small storage capacity as well as read and write speed.
40 * Turn off the Receiver and disconnect all USB devices.
41 * Connect the USB stick with the IRD file to your Receiver
42 * Switch on (mains switch) and at the same time hold the CH + on the unit (about 15 seconds) until "search IRD File ... " appears,
43   and the installation begins. Only then release the button
44     Note: If installation does not start , use a different USB stick.
45 * After successfully installing the receiver will reboot and the installed image should start-up
46[[br]]
47[#point8.1 Top of Page]
48----
49'''8.2 Atemio520''' [=#point8.2] ([wiki:Wiki-en#point0 Contents]) ([WikiStart#point0 Main page])
50----
51
52[[br]]
53
54'' How do I install an Atemio 520 IRD image? ''
55 * Visit the Atemio homepage or the AAF digital forum and download the latest firmware TitanNit .
56 * Extract the zip file
57 * Now copy the unzipped IRD firmware file to a formatted FAT32 USB stick.
58     Note: The USB stick should not be formatted with windows. Use a separate program, such as the
59     " HP USB Disk Storage Format Tool" (freeware program).
60     Furthermore, we recommend a cheap USB stick with a small storage capacity as well as read and write speed.
61 * Turn off the Receiver and disconnect all USB devices.
62 * Connect the USB stick with the IRD file to your Receiver
63 * Switch on (mains switch) and at the same time hold the CH + on the unit (about 15 seconds) until "search IRD File ... " appears,
64   and the installation begins. Only then release the button
65     Note: If installation does not start , use a different USB stick.
66 * After successfully installing the receiver will reboot and the installed image should start-up
67[[br]]
68[#point8.1 Top of Page]
69
70----
71'''8.3 Atemio530''' [=#point8.3] ([wiki:Wiki-en#point0 Contents]) ([WikiStart#point0 Main page])
72----
73
74[[br]]
75'' How do I install an Atemio 530 IRD image? ''
76 * Visit the Atemio homepage or the AAF digital forum and download the latest firmware TitanNit .
77 * Extract the zip file
78 * Now copy the unzipped IRD firmware file to a formatted FAT32 USB stick.
79     Note: The USB stick should not be formatted with windows. Use a separate program, such as the
80     " HP USB Disk Storage Format Tool" (freeware program).
81     Furthermore, we recommend a cheap USB stick with a small storage capacity as well as read and write speed.
82 * Turn off the Receiver and disconnect all USB devices.
83 * Connect the USB stick with the IRD file to your Receiver
84 * Switch on (mains switch) and at the same time hold the CH + on the unit (about 15 seconds) until "search IRD File ... " appears,
85   and the installation begins. Only then release the button
86     Note: If installation does not start , use a different USB stick.
87 * After successfully installing the receiver will reboot and the installed image should start-up
88[[br]]
89[#point8.1 Top of Page]
90
91----
92'''8.4 Atemio7600''' [=#point8.4] ([wiki:Wiki-en#point0 Contents]) ([WikiStart#point0 Main page])
93----
94
95[[br]]
96'' How do I install an Atemio 7600 IRD image? ''
97 * Visit the Atemio homepage or the AAF digital forum and download the latest firmware TitanNit .
98 * Extract the zip file
99 * Now copy the unzipped IRD firmware file to a formatted FAT32 USB stick.
100     Note: The USB stick should not be formatted with windows. Use a separate program, such as the
101     " HP USB Disk Storage Format Tool" (freeware program).
102     Furthermore, we recommend a cheap USB stick with a small storage capacity as well as read and write speed.
103 * Turn off the Receiver and disconnect all USB devices.
104 * Connect the USB stick with the IRD file to your Receiver
105 * Switch on (mains switch) and at the same time hold the CH + on the unit (about 15 seconds) until "search IRD File ... " appears,
106   and the installation begins. Only then release the button
107     Note: If installation does not start , use a different USB stick.
108 * After successfully installing the receiver will reboot and the installed image should start-up
109[[br]]
110[#point8.1 Top of Page]
111
112----
113'''8.5 Atevio700''' [=#point8.5] ([wiki:Wiki-en#point0 Contents]) ([WikiStart#point0 Main page])
114----
115
116[[br]]
117
118'' How do I install an Atemio 700 IRD image? ''
119 * Visit the Atemio homepage or the AAF digital forum and download the latest firmware TitanNit .
120 * Extract the zip file
121 * Now copy the unzipped IRD firmware file to a formatted FAT32 USB stick.
122     Note: The USB stick should not be formatted with windows. Use a separate program, such as the
123     " HP USB Disk Storage Format Tool" (freeware program).
124     Furthermore, we recommend a cheap USB stick with a small storage capacity as well as read and write speed.
125 * Turn off the Receiver and disconnect all USB devices.
126 * Connect the USB stick with the IRD file to your Receiver
127 * Switch on (mains switch) and at the same time hold the CH + on the unit (about 15 seconds) until "search IRD File ... " appears,
128   and the installation begins. Only then release the button
129     Note: If installation does not start , use a different USB stick.
130 * After successfully installing the receiver will reboot and the installed image should start-up
131[[br]]
132[#point8.1 Top of Page]
133
134----
135'''8.6 Atevio7000''' [=#point8.6] ([wiki:Wiki-en#point0 Contents]) ([WikiStart#point0 Main page])
136----
137
138[[br]]
139
140'' How do I install an Atemio 7000 IRD image? ''
141 * Visit the Atemio homepage or the AAF digital forum and download the latest firmware TitanNit .
142 * Extract the zip file
143 * Now copy the unzipped IRD firmware file to a formatted FAT32 USB stick.
144     Note: The USB stick should not be formatted with windows. Use a separate program, such as the
145     " HP USB Disk Storage Format Tool" (freeware program).
146     Furthermore, we recommend a cheap USB stick with a small storage capacity as well as read and write speed.
147 * Turn off the Receiver and disconnect all USB devices.
148 * Connect the USB stick with the IRD file to your Receiver
149 * Switch on (mains switch) and at the same time hold the CH + on the unit (about 15 seconds) until "search IRD File ... " appears,
150   and the installation begins. Only then release the button
151     Note: If installation does not start , use a different USB stick.
152 * After successfully installing the receiver will reboot and the installed image should start-up
153[[br]]
154[#point8.1 Top of Page]
155
156----
157'''8.7 Kathrein Ufs910''' [=#point8.7] ([wiki:Wiki-en#point0 Contents]) ([WikiStart#point0 Main page])
158----
159
160[[br]]
161
162'' How do I install a Kathrein UFS910 update image? ''
163 * When you install a USB .img file the mnt-filesystem is formatted. An Online Update leaves the mnt-filesystem untouched.
164 * Visit the AAF digital forum and download the latest firmware TitanNit .
165 * Extract the zip file
166 * Now copy the unzipped img firmware file - must be renamed to miniFLASH.img - to a formatted FAT32 USB stick.
167     Note: The USB stick should not be formatted with windows, but a separate program, such as the
168     " HP USB Disk Storage Format Tool" (freeware program).
169     Furthermore, we recommend a cheap USB stick with a small storage capacity as well as read and write speed.
170 * Turn off the Receiver and disconnect all USB devices.
171 * Connect the USB stick with the img file to the front USB Port
172 * Switch on (mains switch) and at the same time hold the -Record button- on the Remote Control pressed (about 5 seconds)
173   until "miniFLASH search..." appears, then the installation begins. Only then release the -Record button-
174     Note: If installation does not start, use a different USB stick.
175 * After successfully installing the receiver will reboot and the installed image should start-up
176[[br]]
177[#point8.1 Top of Page]
178
179----
180'''8.8 Kathrein UFS912''' [=#point8.8] ([wiki:Wiki-en#point0 Contents]) ([WikiStart#point0 Main page])
181----
182
183[[br]]
184
185'' How do I install a Kathrein UFS912 update image? ''
186 * Visit the AAF digital forum and download the latest firmware TitanNit .
187 * Extract the zip file
188 * Now copy the unzipped firmware file *_FULL_nodebug.img to a formatted FAT32 USB stick into the path: /kathrein/ufs912/ .
189     Note: The USB stick should not be formatted with windows, but a separate program, such as the
190     " HP USB Disk Storage Format Tool" (freeware program).
191     Furthermore, we recommend a cheap USB stick with a small storage capacity as well as read and write speed.
192 * Turn off the Receiver and disconnect all USB devices.
193 * Connect the USB stick with the img file
194 * Switch on (mains switch) and at the same time press the -TV/Radio button- on the unit (about 5 seconds) until "emergency boot" appears,
195   then the installation begins. Only after that message release the -TV/Radio button-
196     Note: If installation does not start, use a different USB stick.
197 * After successfully installing the receiver will reboot and the installed image should start-up
198[[br]]
199[#point8.1 Top of Page]
200
201----
202'''8.9 Kathrein UFS922''' [=#point8.9] ([wiki:Wiki-en#point0 Contents]) ([WikiStart#point0 Main page])
203----
204
205[[br]]
206
207'' How do I install a Kathrein UFS922 update image? ''
208 * When you install a USB .img file the mnt-filesystem is formatted. An Online Update leaves the mnt-filesystem untouched.
209 * Visit the AAF digital forum and download the latest firmware TitanNit .
210 * Extract the zip file
211 * Now copy the unzipped firmware file *_FULL_nodebug.img to a formatted FAT32 USB stick into the path: /kathrein/ufs922/ .
212     Note: The USB stick should not be formatted with windows, but a separate program, such as the
213     " HP USB Disk Storage Format Tool" (freeware program).
214     Furthermore, we recommend a cheap USB stick with a small storage capacity as well as read and write speed.
215 * Turn off the Receiver and disconnect all USB devices.
216 * Connect the USB stick with the img file
217 * Switch on (mains switch) and at the same time press the -TV/Radio button- on the unit (about 5 seconds) until "emergency boot" appears,
218   then the installation begins. Only after that message release the -TV/Radio button-
219     Note: If installation does not start, use a different USB stick.
220 * After successfully installing the receiver will reboot and the installed image should start-up
221[[br]]
222[#point8.1 Top of Page]
223
224
225----
226'''Instalation on other Fortis Recievers'''  [=#point8.10] ([wiki:Wiki-en#point0 Contents]) ([WikiStart#point0 Main page])
227----
228
229[[br]]
230
231'''Installation Notes:'''
232
233''If you wish to try or install titan you need to install an Atemio/Atevio factory loader. The original Atemio Bootloader has a security code within so an installation of Titan is not possible with any other fortis loader''
234
235''If you wish to install Titan the loader version must be 1.54 or above. Titan versions above 1.32 require the new Iboot loader which needs to be installed first if not present.''
236
237''There are various ways that are explained below:''
238 
239[[br]]
240
241'''AAF Recovery Tool (ART) method'''
242
243 * Install the AAF Recovery Tool (ART) and set up a connection to your receiver
244 * Set the IP address and subnet mask of your uboot environment.
245 * Reboot the receiver and reconnect to change the settings.
246 * Install the factory loader and reboot.
247 * The factory loader you installed is version 1.21 that you have to update to 1.54 to be compatable with Titan
248 * Visit the [http:((www-atemio.de Atemio] homepage or the [http://www.aaf-digital.info/forum AAF digital forum] and download the latest Atevio/Atemio loaader (1.54).
249 * Extract the zip file
250  * Now copy the unzipped IRD firmware file to a formatted FAT32 USB stick.
251     Note: The USB stick should not be formatted with windows. Use a separate program, such as the
252     "HP USB Disk Storage Format Tool" (freeware program).
253     Furthermore, we recommend a cheap USB stick with a small storage capacity as well as read and write speed.
254 * Turn off the receiver and disconnect all USB devices.
255 * Connect the USB stick with the IRD file to your receiver
256 * Switch on (mains switch) and at the same time hold the CH + on the unit (about 15 seconds) until "search IRD File ... " appears,
257   and the installation begins. Only then release the button
258     Note: Should the installation not start, try a different USB stick.
259 * Should you have installed the loader successfully the receiver will reboot and the installed Loader should start-up.
260
261''You may now install Titan''
262[[br]]
263
264
265[[br]]
266
267'''Cross Flash Method'''
268
269''This method explains how to install the HDF bootloader flash plugin to your fortis receiver and flash an Atemio/Atevio compatable bootloader from the plugin menu.''
270
271* Download the HDF Bootloader flash plugin from the [http://www.aaf-digital.info/forum AAF Digital forum].
272 * Extract the zip file
273 * Now copy the unzipped Plugin folder to a formatted FAT32 USB stick.
274     Note: The USB stick should not be formatted with windows. Use a separate program, such as the
275     " HP USB Disk Storage Format Tool" (freeware program).
276     Furthermore, we recommend a cheap USB stick with a small storage capacity as well as read and write speed.
277 * go to the plugins section in your receiver and install the plugin and then start it.
278 * type in the password contained in the zip file and follow the onscreen prompts.
279 * Should you have installed the loader successfully the receiver will reboot and the installed Loader should start-up.
280
281''You may now install TitanNit''
282
283[[br]]
284
285'''Reseller Changer Tool Method'''
286
287''This method explains how to change the Reseler ID of an Atemio/Atevio compatable bootloader and flash it to any compatable Fortis receiver from the plugin menu.''
288
289
290* Visit the [http://www.atemio.de Atemio] homepage or the [http://www.aaf-digital.info/forum AAF digital forum] and download the latest Atevio/Atemio loader.
291 * Extract the zip file
292 * use the reseller ID changer tool and change the IRD to that of your reseller ID.
293 * Now copy the unzipped IRD firmware file to a formatted FAT32 USB stick.
294     Note: The USB stick should not be formatted with windows. Use a separate program, such as the
295     " HP USB Disk Storage Format Tool" (freeware program).
296     Furthermore, we recommend a cheap USB stick with a small storage capacity as well as read and write speed.
297 * Turn off the Receiver and disconnect all USB devices.
298 * Connect the USB stick with the IRD file to your Receiver.
299 * Switch on (mains switch) and at the same time hold the CH + on the unit (about 15 seconds) until "search IRD File ... " appears,
300   and the installation begins. Only then release the button
301     Note: If installation does not start , use a different USB stick.
302 * Should you have installed the loader successfully the receiver will reboot and the installed Loader should start-up.
303
304
305This method requires you to also change the reseller ID to be able to install TitanNit.
306
307
308'''Be aware should it the installation fail or a loss of Power occur during the flashing process you could brick your receiver as there is no recovery method. Compatibility with other receivers is not guaranteed but you may find a list of compatable receivers in the [wiki:Supported-Recievers-en#point7 Supported Receivers] section.'''
309[[br]]
310[#point8.1 Top of Page]
311----
312'''8.11 Uninstalling Titan'' [=#point8.11] ([wiki:Wiki-en#point0 Contents]) ([WikiStart#point0 Main page])
313----
314[[br]]
315
316If you have an Atemio/Atevio or UFS receiver all you have to do is install your original ird file as explained above and no bootloader changes are neccessary.
317
318Uninstalling titan and switching back to the original reseller loader can't be done (easily) for other fortis receivers but there is one simple alternative method outlined below.
319
320
321'''Uninstalling Titan on non Atemio/Atevio receiver and restore Reseller ID with Maxi-uboot'''
322
323If you have iboot installed then you must install a version of TitanNit older than 1.32 before using this method.
324
325This will install the factory Atemio loader that is compatible with the AAF Recovery Tool (ART) to be able to install the Maxiuboot Loader.
326
327In order for this method to work make sure the setting Allow __"Iboot Update"__ is enabled in [wiki:Remote-Device-Control-en#point4.6 Iboot].
328
329When successfully achieved you may start up ART from your PC and install Maxiuboot.
330
331[[br]]
332
333Once installed you may set up your bootargs and change your Reseller ID back to its factory settings. For flashin original Firmware or other Software please refere to your receivers' manual or instructions.
334[[br]]
335[#point108.1 Top of Page]
336 
Note: See TracBrowser for help on using the repository browser.