source: wiki/pages/en/Installation-Recovery @ 28118

Last change on this file since 28118 was 28118, checked in by aafsvn, 6 years ago

[titan] autoupdate wiki files

File size: 19.4 KB
Line 
1----
2'''8 Installation and Recovery Contents''' [=#point8] ([wiki:Wiki#point0 Contents]) ([WikiStart#point0 Main page])
3----
4
5[[br]]
6
7This section contains information on installation and removal of TitanNit from your receiver
8
9[[br]]
10
11 * [#point8.1 8.1 Atemio510 and compatible Models]
12 * [#point8.2 8.2 Atemio520 and compatible Models]
13 * [#point8.3 8.3 Atemio530 and compatible Models]
14 * [#point8.4 8.4 Atemio7600 and compatible Models]
15 * [#point8.5 8.5 Atemio700 and compatible Models]
16 * [#point8.6 8.6 Atemio7000 and compatible Models]
17 * [#point8.6 8.6 Atemio5200 and compatible Models]
18 * [#point8.8 8.8 Ufs910]
19 * [#point8.9 8.9 Ufs912]
20 * [#point8.10 8.10 Ufs922]
21 * [#point8.11 8.11 Installation on other Fortis Receivers]
22 * [#point8.12 8.12 Uninstallation On other Fortis Receivers]
23 * [#point8.13 8.13 Update TitanNit]
24 * [#point8.14 8.14 IRD Download Location]
25
26
27[[br]]
28
29
30----
31'''8.1 Atemio510''' [=#point8.1] ([wiki:Wiki#point0 Contents]) ([WikiStart#point0 Main page])
32----
33
34[[br]]
35
36'' How do I install an Atemio 510 IRD image? ''
37 * Visit the Atemio homepage or the AAF digital forum and download the latest TitanNit firmware .
38 * Extract the zip file
39 * Now copy the unzipped IRD firmware file to a formatted FAT32 USB stick.
40     Note: The USB stick should not be formatted with windows. Use a separate program, such as the
41     " HP USB Disk Storage Format Tool" (freeware program).
42     Furthermore, we recommend a cheap USB stick with a small storage capacity as well as read and write speed.
43 * Turn off the Receiver and disconnect all USB devices.
44 * Connect the USB stick with the IRD file to your Receiver
45 * Switch on (mains switch) and at the same time hold the CH + on the unit (about 15 seconds) until "search IRD File ... " appears,
46   and the installation begins. Only then release the button
47     Note: If installation does not start , use a different USB stick.
48 * After successfully installing the receiver will reboot and the installed image should start-up
49[[br]]
50[#point8.1 Top of Page]
51----
52'''8.2 Atemio520''' [=#point8.2] ([wiki:Wiki#point0 Contents]) ([WikiStart#point0 Main page])
53----
54
55[[br]]
56
57'' How do I install an Atemio 520 IRD image? ''
58 * Visit the Atemio homepage or the AAF digital forum and download the latest TitanNit firmware .
59 * Extract the zip file
60 * Now copy the unzipped IRD firmware file to a formatted FAT32 USB stick.
61     Note: The USB stick should not be formatted with windows. Use a separate program, such as the
62     " HP USB Disk Storage Format Tool" (freeware program).
63     Furthermore, we recommend a cheap USB stick with a small storage capacity as well as read and write speed.
64 * Turn off the Receiver and disconnect all USB devices.
65 * Connect the USB stick with the IRD file to your Receiver
66 * Switch on (mains switch) and at the same time hold the CH + on the unit (about 15 seconds) until "search IRD File ... " appears,
67   and the installation begins. Only then release the button
68     Note: If installation does not start , use a different USB stick.
69 * After successfully installing the receiver will reboot and the installed image should start-up
70[[br]]
71[#point8.1 Top of Page]
72
73----
74'''8.3 Atemio530''' [=#point8.3] ([wiki:Wiki#point0 Contents]) ([WikiStart#point0 Main page])
75----
76
77[[br]]
78'' How do I install an Atemio 530 IRD image? ''
79 * Visit the Atemio homepage or the AAF digital forum and download the latest TitanNit firmware .
80 * Extract the zip file
81 * Now copy the unzipped IRD firmware file to a formatted FAT32 USB stick.
82     Note: The USB stick should not be formatted with windows. Use a separate program, such as the
83     " HP USB Disk Storage Format Tool" (freeware program).
84     Furthermore, we recommend a cheap USB stick with a small storage capacity as well as read and write speed.
85 * Turn off the Receiver and disconnect all USB devices.
86 * Connect the USB stick with the IRD file to your Receiver
87 * Switch on (mains switch) and at the same time hold the CH + on the unit (about 15 seconds) until "search IRD File ... " appears,
88   and the installation begins. Only then release the button
89     Note: If installation does not start , use a different USB stick.
90 * After successfully installing the receiver will reboot and the installed image should start-up
91[[br]]
92[#point8.1 Top of Page]
93
94----
95'''8.4 Atemio7600''' [=#point8.4] ([wiki:Wiki#point0 Contents]) ([WikiStart#point0 Main page])
96----
97
98[[br]]
99'' How do I install an Atemio 7600 IRD image? ''
100 * Visit the Atemio homepage or the AAF digital forum and download the latest TitanNit firmware .
101 * Extract the zip file
102 * Now copy the unzipped IRD firmware file to a formatted FAT32 USB stick.
103     Note: The USB stick should not be formatted with windows. Use a separate program, such as the
104     " HP USB Disk Storage Format Tool" (freeware program).
105     Furthermore, we recommend a cheap USB stick with a small storage capacity as well as read and write speed.
106 * Turn off the Receiver and disconnect all USB devices.
107 * Connect the USB stick with the IRD file to your Receiver
108 * Switch on (mains switch) and at the same time hold the CH + on the unit (about 15 seconds) until "search IRD File ... " appears,
109   and the installation begins. Only then release the button
110     Note: If installation does not start , use a different USB stick.
111 * After successfully installing the receiver will reboot and the installed image should start-up
112[[br]]
113[#point8.1 Top of Page]
114
115----
116'''8.5 Atevio700''' [=#point8.5] ([wiki:Wiki#point0 Contents]) ([WikiStart#point0 Main page])
117----
118
119[[br]]
120
121'' How do I install an Atemio 700 IRD image? ''
122 * Visit the Atemio homepage or the AAF digital forum and download the latest TitanNit firmware .
123 * Extract the zip file
124 * Now copy the unzipped IRD firmware file to a formatted FAT32 USB stick.
125     Note: The USB stick should not be formatted with windows. Use a separate program, such as the
126     " HP USB Disk Storage Format Tool" (freeware program).
127     Furthermore, we recommend a cheap USB stick with a small storage capacity as well as read and write speed.
128 * Turn off the Receiver and disconnect all USB devices.
129 * Connect the USB stick with the IRD file to your Receiver
130 * Switch on (mains switch) and at the same time hold the CH + on the unit (about 15 seconds) until "search IRD File ... " appears,
131   and the installation begins. Only then release the button
132     Note: If installation does not start , use a different USB stick.
133 * After successfully installing the receiver will reboot and the installed image should start-up
134[[br]]
135[#point8.1 Top of Page]
136
137----
138'''8.6 Atevio7000''' [=#point8.6] ([wiki:Wiki#point0 Contents]) ([WikiStart#point0 Main page])
139----
140
141[[br]]
142
143'' How do I install an Atemio 7000 IRD image? ''
144 * Visit the Atemio homepage or the AAF digital forum and download the latest TitanNit firmware .
145 * Extract the zip file
146 * Now copy the unzipped IRD firmware file to a formatted FAT32 USB stick.
147     Note: The USB stick should not be formatted with windows. Use a separate program, such as the
148     " HP USB Disk Storage Format Tool" (freeware program).
149     Furthermore, we recommend a cheap USB stick with a small storage capacity as well as read and write speed.
150 * Turn off the Receiver and disconnect all USB devices.
151 * Connect the USB stick with the IRD file to your Receiver
152 * Switch on (mains switch) and at the same time hold the CH + on the unit (about 15 seconds) until "search IRD File ... " appears,
153   and the installation begins. Only then release the button
154     Note: If installation does not start , use a different USB stick.
155 * After successfully installing the receiver will reboot and the installed image should start-up
156[[br]]
157[#point8.1 Top of Page]
158
159----
160'''8.7 Atevio5200''' [=#point8.7] ([wiki:Wiki#point0 Contents]) ([WikiStart#point0 Main page])
161----
162
163[[br]]
164
165'' How do I install an Atemio 5200 image? ''
166
167Currently we dont have this information available and will be updated in the future to reflect this
168
169[[br]]
170[#point8.1 Top of Page]
171
172
173----
174'''8.8 Kathrein Ufs910''' [=#point8.8] ([wiki:Wiki#point0 Contents]) ([WikiStart#point0 Main page])
175----
176
177[[br]]
178
179'' How do I install a Kathrein UFS910 update image? ''
180 * When you install a USB .img file the mnt-filesystem is formatted. An Online Update leaves the mnt-filesystem untouched.
181 * Visit the AAF digital forum and download the latest TitanNit firmware .
182 * Extract the zip file
183 * Now copy the unzipped img firmware file - must be renamed to miniFLASH.img - to a formatted FAT32 USB stick.
184     Note: The USB stick should not be formatted with windows, but a separate program, such as the
185     " HP USB Disk Storage Format Tool" (freeware program).
186     Furthermore, we recommend a cheap USB stick with a small storage capacity as well as read and write speed.
187 * Turn off the Receiver and disconnect all USB devices.
188 * Connect the USB stick with the img file to the front USB Port
189 * Switch on (mains switch) and at the same time hold the -Record button- on the Remote Control pressed (about 5 seconds)
190   until "miniFLASH search..." appears, then the installation begins. Only then release the -Record button-
191     Note: If installation does not start, use a different USB stick.
192 * After successfully installing the receiver will reboot and the installed image should start-up
193[[br]]
194[#point8.1 Top of Page]
195
196----
197'''8.9 Kathrein UFS912''' [=#point8.9] ([wiki:Wiki#point0 Contents]) ([WikiStart#point0 Main page])
198----
199
200[[br]]
201
202'' How do I install a Kathrein UFS912 update image? ''
203 * Visit the AAF digital forum and download the latest TitanNit firmware .
204 * Extract the zip file
205 * Now copy the unzipped firmware file *_FULL_nodebug.img to a formatted FAT32 USB stick into the path: /kathrein/ufs912/ .
206     Note: The USB stick should not be formatted with windows, but a separate program, such as the
207     " HP USB Disk Storage Format Tool" (freeware program).
208     Furthermore, we recommend a cheap USB stick with a small storage capacity as well as read and write speed.
209 * Turn off the Receiver and disconnect all USB devices.
210 * Connect the USB stick with the img file
211 * Switch on (mains switch) and at the same time press the -TV/Radio button- on the unit (about 5 seconds) until "emergency boot" appears,
212   then the installation begins. Only after that message release the -TV/Radio button-
213     Note: If installation does not start, use a different USB stick.
214 * After successfully installing the receiver will reboot and the installed image should start-up
215[[br]]
216[#point8.1 Top of Page]
217
218----
219'''8.10 Kathrein UFS922''' [=#point8.10] ([wiki:Wiki#point0 Contents]) ([WikiStart#point0 Main page])
220----
221
222[[br]]
223
224'' How do I install a Kathrein UFS922 update image? ''
225 * When you install a USB .img file the mnt-filesystem is formatted. An Online Update leaves the mnt-filesystem untouched.
226 * Visit the AAF digital forum and download the latest TitanNit firmware .
227 * Extract the zip file
228 * Now copy the unzipped firmware file *_FULL_nodebug.img to a formatted FAT32 USB stick into the path: /kathrein/ufs922/ .
229     Note: The USB stick should not be formatted with windows, but a separate program, such as the
230     " HP USB Disk Storage Format Tool" (freeware program).
231     Furthermore, we recommend a cheap USB stick with a small storage capacity as well as read and write speed.
232 * Turn off the Receiver and disconnect all USB devices.
233 * Connect the USB stick with the img file
234 * Switch on (mains switch) and at the same time press the -TV/Radio button- on the unit (about 5 seconds) until "emergency boot" appears,
235   then the installation begins. Only after that message release the -TV/Radio button-
236     Note: If installation does not start, use a different USB stick.
237 * After successfully installing the receiver will reboot and the installed image should start-up
238[[br]]
239[#point8.1 Top of Page]
240
241
242----
243'''8.11 installation on other Fortis Receivers'''  [=#point8.11] ([wiki:Wiki#point0 Contents]) ([WikiStart#point0 Main page])
244----
245
246[[br]]
247
248'''Installation Notes:'''
249
250''If you wish to try or install titan you need to install an Atemio/Atevio factory loader. The original Atemio Bootloader has a security code within so an installation of Titan is not possible with any other fortis loader''
251
252''If you wish to install Titan the loader version must be 1.54 or above. Titan versions above 1.32 require the new Iboot loader which needs to be installed first if not present.''
253
254''There are various ways that are explained below:''
255 
256[[br]]
257
258'''AAF Recovery Tool (ART) method'''
259
260 * Install the AAF Recovery Tool (ART) and set up a connection to your receiver
261 * Set the IP address and subnet mask of your uboot environment.
262 * Reboot the receiver and reconnect to change the settings.
263 * Install the factory loader and reboot.
264 * The factory loader you installed is version 1.21 that you have to update to 1.54 to be compatible with Titan
265 * Visit the [http:((www-atemio.de Atemio] homepage or the [http://www.aaf-digital.info/forum AAF digital forum] and download the latest Atevio/Atemio loaader (1.54).
266 * Extract the zip file
267  * Now copy the unzipped IRD firmware file to a formatted FAT32 USB stick.
268     Note: The USB stick should not be formatted with windows. Use a separate program, such as the
269     "HP USB Disk Storage Format Tool" (freeware program).
270     Furthermore, we recommend a cheap USB stick with a small storage capacity as well as read and write speed.
271 * Turn off the receiver and disconnect all USB devices.
272 * Connect the USB stick with the IRD file to your receiver
273 * Switch on (mains switch) and at the same time hold the CH + on the unit (about 15 seconds) until "search IRD File ... " appears,
274   and the installation begins. Only then release the button
275     Note: Should the installation not start, try a different USB stick.
276 * Should you have installed the loader successfully the receiver will reboot and the installed Loader should start-up.
277
278''You may now install Titan''
279[[br]]
280
281
282[[br]]
283
284'''Cross Flash Method'''
285
286''This method explains how to install the HDF bootloader flash plugin to your fortis receiver and flash an Atemio/Atevio compatible bootloader from the plugin menu.''
287
288* Download the HDF Bootloader flash plugin from the [http://www.aaf-digital.info/forum AAF Digital forum].
289 * Extract the zip file
290 * Now copy the unzipped Plugin folder to a formatted FAT32 USB stick.
291     Note: The USB stick should not be formatted with windows. Use a separate program, such as the
292     " HP USB Disk Storage Format Tool" (freeware program).
293     Furthermore, we recommend a cheap USB stick with a small storage capacity as well as read and write speed.
294 * go to the plugins section in your receiver and install the plugin and then start it.
295 * type in the password contained in the zip file and follow the onscreen prompts.
296 * Should you have installed the loader successfully the receiver will reboot and the installed Loader should start-up.
297
298''You may now install TitanNit''
299
300[[br]]
301
302'''Reseller Changer Tool Method'''
303
304''This method explains how to change the Reseler ID of an Atemio/Atevio compatible bootloader and flash it to any compatible Fortis receiver from the plugin menu.''
305
306
307* Visit the [http://www.atemio.de Atemio] homepage or the [http://www.aaf-digital.info/forum AAF digital forum] and download the latest Atevio/Atemio loader.
308 * Extract the zip file
309 * use the reseller ID changer tool and change the IRD to that of your reseller ID.
310 * Now copy the unzipped IRD firmware file to a formatted FAT32 USB stick.
311     Note: The USB stick should not be formatted with windows. Use a separate program, such as the
312     " HP USB Disk Storage Format Tool" (freeware program).
313     Furthermore, we recommend a cheap USB stick with a small storage capacity as well as read and write speed.
314 * Turn off the Receiver and disconnect all USB devices.
315 * Connect the USB stick with the IRD file to your Receiver.
316 * Switch on (mains switch) and at the same time hold the CH + on the unit (about 15 seconds) until "search IRD File ... " appears,
317   and the installation begins. Only then release the button
318     Note: If installation does not start , use a different USB stick.
319 * Should you have installed the loader successfully the receiver will reboot and the installed Loader should start-up.
320
321
322This method requires you to also change the reseller ID to be able to install TitanNit.
323
324
325'''Be aware should it the installation fail or a loss of Power occur during the flashing process you could brick your receiver as there is no recovery method. Compatibility with other receivers is not guaranteed but you may find a list of compatible receivers in the [wiki:Supported-Receivers#point7 Supported Receivers] section.'''
326[[br]]
327[#point8.1 Top of Page]
328----
329'''8.12 Uninstalling Titan'' [=#point8.12] ([wiki:Wiki#point0 Contents]) ([WikiStart#point0 Main page])
330----
331[[br]]
332
333If you have an Atemio/Atevio or UFS receiver all you have to do is install your original ird file as explained above and no bootloader changes are neccessary.
334
335Uninstalling titan and switching back to the original reseller loader can't be done (easily) for other fortis receivers but there is one simple alternative method outlined below.
336
337
338'''Uninstalling Titan on non Atemio/Atevio receiver and restore Reseller ID with Maxi-uboot'''
339
340If you have iboot installed then you must install a version of TitanNit older than 1.32 before using this method.
341
342This will install the factory Atemio loader that is compatible with the AAF Recovery Tool (ART) to be able to install the Maxiuboot Loader.
343
344In order for this method to work make sure the setting Allow __"Iboot Update"__ is enabled in [wiki:Remote-Device-Control#point4.6 Iboot].
345
346When successfully achieved you may start up ART from your PC and install Maxiuboot.
347
348[[br]]
349
350Once installed you may set up your bootargs and change your Reseller ID back to its factory settings. For flashin original Firmware or other Software please refere to your receivers' manual or instructions.
351[[br]]
352[#point108.1 Top of Page]
353
354
355----   
356'''8.13 Update TitanNit[=#point8.13] ([wiki:Wiki#point0 Contents]) ([WikiStart#point0 Main Page]) 
357---- 
358[[br]] 
359
360There are two ways to update your TitanNit version and there are merits to both methods :
361
362IRD offline method see [#point8 Installation / Recovery Inhaltsverzeichnis] and select your Reciever model to show information on how to update titan using an IRD titannit image.
363[[br]]
364''Note: using this method plugins and files stored to Flash will be formatted when the update is proformed.
365Plugins and files installed to MNT (except on the ufs 910/922) or a valid configured storage device will retain there settings .''
366
367Image Online Method see [wiki:System-Update#point3.5.7 System aktualisieren] for information on how preform an online update.
368[[br]]
369''Note: using this method all plugins and settings are retained as long as they are not installed in flash.''
370
371[[br]]
372
373[#point8 Top of Page]
374
375[[br]]
376
377----   
378'''8.14 IRD Download Locations'' [=#point8.14] ([wiki:Wiki#point0 Contents]) ([WikiStart#point0 Main Page]) 
379---- 
380[[br]] 
381
382* [wiki:Manufactures#point13 13 Manufactures] - [http://atemio.de/index.php/software-updates Stable Images][[br]] 
383* [wiki:Community#point14 14 Community] - [http://www.aaf-digital.info/forum/downloads.php?do=cat&id=2 Stable Images] [http://www.aaf-digital.info/forum/pages.php?pageid=12 Nightly Images][[br]] 
384 
385[[br]] 
386[#point8 Top of Page] 
387[[br]] 
388[[br]] 
389[[br]] 
390 
Note: See TracBrowser for help on using the repository browser.