source: wiki/pages/en/Installation-Recovery @ 28190

Last change on this file since 28190 was 28190, checked in by aafsvn, 6 years ago

[titan] autoupdate wiki files

File size: 21.9 KB
Line 
1----
2'''8 Installation and Recovery Contents''' [=#point8] ([wiki:Wiki#point0 Contents]) ([WikiStart#point0 Main page])
3----
4
5[[br]]
6
7This section contains information on installation and removal of TitanNit from your receiver
8[[br]]
9'''SH4 Models'''
10
11 * [#point8.1 8.1 Atemio510 and compatible Models]
12 * [#point8.2 8.2 Atemio520 and compatible Models]
13 * [#point8.3 8.3 Atemio530 and compatible Models]
14 * [#point8.4 8.4 Atemio7600 and compatible Models]
15 * [#point8.5 8.5 Atemio700 and compatible Models]
16 * [#point8.6 8.6 Atemio7000 and compatible Models]
17 * [#point8.8 8.7 Ufs910]
18 * [#point8.9 8.8 Ufs912]
19 * [#point8.10 8.9 Ufs922]
20
21'''MIPS Models'''
22
23 * [#point8.14 8.10 Atemio5000]
24 * [#point8.15 8.11 Atemio5200]
25
26'''Aditional Info'''
27 
28 * [#point8.11 8.12 Installation on other Fortis Receivers]
29 * [#point8.12 8.13 Uninstallation On other Fortis Receivers]
30 * [#point8.13 8.14 Update TitanNit]
31 * [#point8.14 8.15 IRD Download Location]
32[[br]]
33[[br]]
34[[br]]
35
36
37'''SH4 Models'''
38----
39'''8.1 Atemio510''' [=#point8.1] ([wiki:Wiki#point0 Contents]) ([WikiStart#point0 Main page])
40----
41'' How do I install an Atemio 510 IRD image? ''
42 * Visit the Atemio homepage or the AAF digital forum and download the latest TitanNit firmware . ([#point8.15 IRD Download Locations])
43 * Extract the zip file
44 * Now copy the unzipped IRD firmware file to a formatted FAT32 USB stick.
45     Note: The USB stick should not be formatted with windows. Use a separate program, such as the
46     " HP USB Disk Storage Format Tool" (freeware program).
47     Furthermore, we recommend a cheap USB stick with a small storage capacity as well as read and write speed.
48 * Turn off the Receiver and disconnect all USB devices.
49 * Connect the USB stick with the IRD file to your Receiver
50 * Switch on (mains switch) and at the same time hold the CH + on the unit (about 15 seconds) until "search IRD File ... " appears,
51   and the installation begins. Only then release the button
52     Note: If installation does not start , use a different USB stick.
53 * After successfully installing the receiver will reboot and the installed image should start-up
54[[br]]
55[#point8.1 Top of Page]
56[[br]]
57
58----
59'''8.2 Atemio520''' [=#point8.2] ([wiki:Wiki#point0 Contents]) ([WikiStart#point0 Main page])
60----
61'' How do I install an Atemio 520 IRD image? ''
62 * Visit the Atemio homepage or the AAF digital forum and download the latest TitanNit firmware . ([#point8.15 IRD Download Locations])
63 * Extract the zip file
64 * Now copy the unzipped IRD firmware file to a formatted FAT32 USB stick.
65     Note: The USB stick should not be formatted with windows. Use a separate program, such as the
66     " HP USB Disk Storage Format Tool" (freeware program).
67     Furthermore, we recommend a cheap USB stick with a small storage capacity as well as read and write speed.
68 * Turn off the Receiver and disconnect all USB devices.
69 * Connect the USB stick with the IRD file to your Receiver
70 * Switch on (mains switch) and at the same time hold the CH + on the unit (about 15 seconds) until "search IRD File ... " appears,
71   and the installation begins. Only then release the button
72     Note: If installation does not start , use a different USB stick.
73 * After successfully installing the receiver will reboot and the installed image should start-up
74[[br]]
75[#point8.1 Top of Page]
76
77----
78'''8.3 Atemio530''' [=#point8.3] ([wiki:Wiki#point0 Contents]) ([WikiStart#point0 Main page])
79----
80'' How do I install an Atemio 530 IRD image? ''
81 * Visit the Atemio homepage or the AAF digital forum and download the latest TitanNit firmware . ([#point8.15 IRD Download Locations])
82 * Extract the zip file
83 * Now copy the unzipped IRD firmware file to a formatted FAT32 USB stick.
84     Note: The USB stick should not be formatted with windows. Use a separate program, such as the
85     " HP USB Disk Storage Format Tool" (freeware program).
86     Furthermore, we recommend a cheap USB stick with a small storage capacity as well as read and write speed.
87 * Turn off the Receiver and disconnect all USB devices.
88 * Connect the USB stick with the IRD file to your Receiver
89 * Switch on (mains switch) and at the same time hold the CH + on the unit (about 15 seconds) until "search IRD File ... " appears,
90   and the installation begins. Only then release the button
91     Note: If installation does not start , use a different USB stick.
92 * After successfully installing the receiver will reboot and the installed image should start-up
93[[br]]
94[#point8.1 Top of Page]
95[[br]]
96
97----
98'''8.4 Atemio7600''' [=#point8.4] ([wiki:Wiki#point0 Contents]) ([WikiStart#point0 Main page])
99----
100'' How do I install an Atemio 7600 IRD image? ''
101 * Visit the Atemio homepage or the AAF digital forum and download the latest TitanNit firmware . ([#point8.15 IRD Download Locations])
102 * Extract the zip file
103 * Now copy the unzipped IRD firmware file to a formatted FAT32 USB stick.
104     Note: The USB stick should not be formatted with windows. Use a separate program, such as the
105     " HP USB Disk Storage Format Tool" (freeware program).
106     Furthermore, we recommend a cheap USB stick with a small storage capacity as well as read and write speed.
107 * Turn off the Receiver and disconnect all USB devices.
108 * Connect the USB stick with the IRD file to your Receiver
109 * Switch on (mains switch) and at the same time hold the CH + on the unit (about 15 seconds) until "search IRD File ... " appears,
110   and the installation begins. Only then release the button
111     Note: If installation does not start , use a different USB stick.
112 * After successfully installing the receiver will reboot and the installed image should start-up
113[[br]]
114[#point8.1 Top of Page]
115[[br]]
116
117----
118'''8.5 Atevio700''' [=#point8.5] ([wiki:Wiki#point0 Contents]) ([WikiStart#point0 Main page])
119----
120'' How do I install an Atemio 7600 IRD image? ''
121 * Visit the Atemio homepage or the AAF digital forum and download the latest TitanNit firmware . ([#point8.15 IRD Download Locations])
122 * Extract the zip file
123 * Now copy the unzipped IRD firmware file to a formatted FAT32 USB stick.
124     Note: The USB stick should not be formatted with windows. Use a separate program, such as the
125     " HP USB Disk Storage Format Tool" (freeware program).
126     Furthermore, we recommend a cheap USB stick with a small storage capacity as well as read and write speed.
127 * Turn off the Receiver and disconnect all USB devices.
128 * Connect the USB stick with the IRD file to your Receiver
129 * Switch on (mains switch) and at the same time hold the CH + on the unit (about 15 seconds) until "search IRD File ... " appears,
130   and the installation begins. Only then release the button
131     Note: If installation does not start , use a different USB stick.
132 * After successfully installing the receiver will reboot and the installed image should start-up
133[[br]]
134[#point8.1 Top of Page]
135[[br]]
136
137----
138'''8.6 Atevio7000''' [=#point8.6] ([wiki:Wiki#point0 Contents]) ([WikiStart#point0 Main page])
139----
140'' How do I install an Atemio 7000 IRD image? ''
141 * Visit the Atemio homepage or the AAF digital forum and download the latest TitanNit firmware . ([#point8.15 IRD Download Locations])
142 * Extract the zip file
143 * Now copy the unzipped IRD firmware file to a formatted FAT32 USB stick.
144     Note: The USB stick should not be formatted with windows. Use a separate program, such as the
145     " HP USB Disk Storage Format Tool" (freeware program).
146     Furthermore, we recommend a cheap USB stick with a small storage capacity as well as read and write speed.
147 * Turn off the Receiver and disconnect all USB devices.
148 * Connect the USB stick with the IRD file to your Receiver
149 * Switch on (mains switch) and at the same time hold the CH + on the unit (about 15 seconds) until "search IRD File ... " appears,
150   and the installation begins. Only then release the button
151     Note: If installation does not start , use a different USB stick.
152 * After successfully installing the receiver will reboot and the installed image should start-up
153[[br]]
154[#point8.1 Top of Page]
155[[br]]
156
157----
158'''8.7 Kathrein Ufs910''' [=#point8.7] ([wiki:Wiki#point0 Contents]) ([WikiStart#point0 Main page])
159----
160'' How do I install a Kathrein UFS910 update image? ''
161 * When you install a USB .img file the mnt-filesystem is formatted. An Online Update leaves the mnt-filesystem untouched.
162 * Visit the AAF digital forum and download the latest TitanNit firmware .
163 * Extract the zip file
164 * Now copy the unzipped img firmware file - must be renamed to miniFLASH.img - to a formatted FAT32 USB stick.
165     Note: The USB stick should not be formatted with windows, but a separate program, such as the
166     " HP USB Disk Storage Format Tool" (freeware program).
167     Furthermore, we recommend a cheap USB stick with a small storage capacity as well as read and write speed.
168 * Turn off the Receiver and disconnect all USB devices.
169 * Connect the USB stick with the img file to the front USB Port
170 * Switch on (mains switch) and at the same time hold the -Record button- on the Remote Control pressed (about 5 seconds)
171   until "miniFLASH search..." appears, then the installation begins. Only then release the -Record button-
172     Note: If installation does not start, use a different USB stick.
173 * After successfully installing the receiver will reboot and the installed image should start-up
174[[br]]
175[#point8.1 Top of Page]
176[[br]]
177
178----
179'''8.8 Kathrein UFS912''' [=#point8.8] ([wiki:Wiki#point0 Contents]) ([WikiStart#point0 Main page])
180----
181'' How do I install a Kathrein UFS912 update image? ''
182 * Visit the AAF digital forum and download the latest TitanNit firmware .
183 * Extract the zip file
184 * Now copy the unzipped firmware file *_FULL_nodebug.img to a formatted FAT32 USB stick into the path: /kathrein/ufs912/ .
185     Note: The USB stick should not be formatted with windows, but a separate program, such as the
186     " HP USB Disk Storage Format Tool" (freeware program).
187     Furthermore, we recommend a cheap USB stick with a small storage capacity as well as read and write speed.
188 * Turn off the Receiver and disconnect all USB devices.
189 * Connect the USB stick with the img file
190 * Switch on (mains switch) and at the same time press the -TV/Radio button- on the unit (about 5 seconds) until "emergency boot" appears,
191   then the installation begins. Only after that message release the -TV/Radio button-
192     Note: If installation does not start, use a different USB stick.
193 * After successfully installing the receiver will reboot and the installed image should start-up
194[[br]]
195[#point8.1 Top of Page]
196[[br]]
197
198----
199'''8.9 Kathrein UFS922''' [=#point8.9] ([wiki:Wiki#point0 Contents]) ([WikiStart#point0 Main page])
200----
201'' How do I install a Kathrein UFS922 update image? ''
202 * When you install a USB .img file the mnt-filesystem is formatted. An Online Update leaves the mnt-filesystem untouched.
203 * Visit the AAF digital forum and download the latest TitanNit firmware .
204 * Extract the zip file
205 * Now copy the unzipped firmware file *_FULL_nodebug.img to a formatted FAT32 USB stick into the path: /kathrein/ufs922/ .
206     Note: The USB stick should not be formatted with windows, but a separate program, such as the
207     " HP USB Disk Storage Format Tool" (freeware program).
208     Furthermore, we recommend a cheap USB stick with a small storage capacity as well as read and write speed.
209 * Turn off the Receiver and disconnect all USB devices.
210 * Connect the USB stick with the img file
211 * Switch on (mains switch) and at the same time press the -TV/Radio button- on the unit (about 5 seconds) until "emergency boot" appears,
212   then the installation begins. Only after that message release the -TV/Radio button-
213     Note: If installation does not start, use a different USB stick.
214 * After successfully installing the receiver will reboot and the installed image should start-up
215[[br]]
216[#point8.1 Top of Page]
217[[br]]
218[[br]]
219[[br]]
220
221'''Mips Models'''
222----
223'''8.10 Atevio5000''' [=#point8.10] ([wiki:Wiki#point0 Contents]) ([WikiStart#point0 Main page])
224----
225'' How do I install an Atemio 5000 Update UBI image? ''
226 * Visit the Atemio homepage or the AAF digital forum and download the latest TitanNit firmware . ([#point8.15 IRD Download Locations])
227 * Extract the zip file
228 * Now copy the unzipped IRD firmware file to a formatted FAT32 USB stick.
229    Note: After unpacking two subfolders atemio/5x00 will be created . The USB stick should not be formatted with windows. Use a separate program, such as the " HP USB Disk Storage Format Tool" (freeware program).
230     Furthermore, we recommend a cheap USB stick with a small storage capacity as well as read and write speed.
231 * Turn off the Receiver and disconnect all USB devices.
232 * Connect the USB stick with the IRD file to your Receiver
233 * Switch on ( mains plug ) and press the CH + on the unit (1 button from the right ) until the Vfd ( LCD Display) displayes " Flashing ...".
234   then the installation begins, Only then release the button.
235    Note: If installation does not start , use a different USB stick.
236 * After successfully installing the receiver will reboot and the installed image should start-up
237[[br]]
238[#point8.1 Top of Page]
239[[br]]
240
241----
242'''8.11 Atevio5200''' [=#point8.11] ([wiki:Wiki#point0 Contents]) ([WikiStart#point0 Main page])
243----
244'' How do I install an Atemio 5200 Update UBI image? ''
245 * Visit the Atemio homepage or the AAF digital forum and download the latest TitanNit firmware . ([#point8.15 IRD Download Locations])
246 * Extract the zip file
247 * Now copy the unzipped IRD firmware file to a formatted FAT32 USB stick.
248    Note: After unpacking two subfolders atemio/5x00 will be created . The USB stick should not be formatted with windows. Use a separate program, such as the " HP USB Disk Storage Format Tool" (freeware program).
249     Furthermore, we recommend a cheap USB stick with a small storage capacity as well as read and write speed.
250 * Turn off the Receiver and disconnect all USB devices.
251 * Connect the USB stick with the IRD file to your Receiver
252 * Switch on ( mains plug ) and press the CH + on the unit (1 button from the right ) until the Vfd ( LCD Display) displayes " Flashing ...".
253   then the installation begins, Only then release the button.
254    Note: If installation does not start , use a different USB stick.
255 * After successfully installing the receiver will reboot and the installed image should start-up
256[[br]]
257[#point8.1 Top of Page]
258[[br]]
259[[br]]
260[[br]]
261
262
263'''Mips Models'''----
264'''8.12 installation on other Fortis Receivers'''  [=#point8.12] ([wiki:Wiki#point0 Contents]) ([WikiStart#point0 Main page])
265----
266'''Installation Notes:'''
267
268''If you wish to try or install titan you need to install an Atemio/Atevio factory loader. The original Atemio Bootloader has a security code within so an installation of Titan is not possible with any other fortis loader''
269
270''If you wish to install Titan the loader version must be 1.54 or above. Titan versions above 1.32 require the new Iboot loader which needs to be installed first if not present.''
271
272''There are various ways that are explained below:''
273 
274[[br]]
275
276'''AAF Recovery Tool (ART) method'''
277
278 * Install the AAF Recovery Tool (ART) and set up a connection to your receiver
279 * Set the IP address and subnet mask of your uboot environment.
280 * Reboot the receiver and reconnect to change the settings.
281 * Install the factory loader and reboot.
282 * The factory loader you installed is version 1.21 that you have to update to 1.54 to be compatible with Titan
283 * Visit the [http:((www-atemio.de Atemio] homepage or the [http://www.aaf-digital.info/forum AAF digital forum] and download the latest Atevio/Atemio loaader (1.54).
284 * Extract the zip file
285  * Now copy the unzipped IRD firmware file to a formatted FAT32 USB stick.
286     Note: The USB stick should not be formatted with windows. Use a separate program, such as the
287     "HP USB Disk Storage Format Tool" (freeware program).
288     Furthermore, we recommend a cheap USB stick with a small storage capacity as well as read and write speed.
289 * Turn off the receiver and disconnect all USB devices.
290 * Connect the USB stick with the IRD file to your receiver
291 * Switch on (mains switch) and at the same time hold the CH + on the unit (about 15 seconds) until "search IRD File ... " appears,
292   and the installation begins. Only then release the button
293     Note: Should the installation not start, try a different USB stick.
294 * Should you have installed the loader successfully the receiver will reboot and the installed Loader should start-up.
295
296''You may now install Titan''
297[[br]]
298
299
300[[br]]
301
302'''Cross Flash Method'''
303
304''This method explains how to install the HDF bootloader flash plugin to your fortis receiver and flash an Atemio/Atevio compatible bootloader from the plugin menu.''
305
306* Download the HDF Bootloader flash plugin from the [http://www.aaf-digital.info/forum AAF Digital forum].
307 * Extract the zip file
308 * Now copy the unzipped Plugin folder to a formatted FAT32 USB stick.
309     Note: The USB stick should not be formatted with windows. Use a separate program, such as the
310     " HP USB Disk Storage Format Tool" (freeware program).
311     Furthermore, we recommend a cheap USB stick with a small storage capacity as well as read and write speed.
312 * go to the plugins section in your receiver and install the plugin and then start it.
313 * type in the password contained in the zip file and follow the onscreen prompts.
314 * Should you have installed the loader successfully the receiver will reboot and the installed Loader should start-up.
315
316''You may now install TitanNit''
317
318[[br]]
319
320'''Reseller Changer Tool Method'''
321
322''This method explains how to change the Reseler ID of an Atemio/Atevio compatible bootloader and flash it to any compatible Fortis receiver from the plugin menu.''
323
324
325* Visit the [http://www.atemio.de Atemio] homepage or the [http://www.aaf-digital.info/forum AAF digital forum] and download the latest Atevio/Atemio loader.
326 * Extract the zip file
327 * use the reseller ID changer tool and change the IRD to that of your reseller ID.
328 * Now copy the unzipped IRD firmware file to a formatted FAT32 USB stick.
329     Note: The USB stick should not be formatted with windows. Use a separate program, such as the
330     " HP USB Disk Storage Format Tool" (freeware program).
331     Furthermore, we recommend a cheap USB stick with a small storage capacity as well as read and write speed.
332 * Turn off the Receiver and disconnect all USB devices.
333 * Connect the USB stick with the IRD file to your Receiver.
334 * Switch on (mains switch) and at the same time hold the CH + on the unit (about 15 seconds) until "search IRD File ... " appears,
335   and the installation begins. Only then release the button
336     Note: If installation does not start , use a different USB stick.
337 * Should you have installed the loader successfully the receiver will reboot and the installed Loader should start-up.
338
339
340This method requires you to also change the reseller ID to be able to install TitanNit.
341
342
343'''Be aware should it the installation fail or a loss of Power occur during the flashing process you could brick your receiver as there is no recovery method. Compatibility with other receivers is not guaranteed but you may find a list of compatible receivers in the [wiki:Supported-Receivers#point7 Supported Receivers] section.'''
344[[br]]
345[#point8.1 Top of Page]
346----
347'''8.13 Uninstalling Titan'' [=#point8.13] ([wiki:Wiki#point0 Contents]) ([WikiStart#point0 Main page])
348----
349If you have an Atemio/Atevio or UFS receiver all you have to do is install your original ird file as explained above and no bootloader changes are neccessary.
350
351Uninstalling titan and switching back to the original reseller loader can't be done (easily) for other fortis receivers but there is one simple alternative method outlined below.
352
353
354'''Uninstalling Titan on non Atemio/Atevio receiver and restore Reseller ID with Maxi-uboot'''
355
356If you have iboot installed then you must install a version of TitanNit older than 1.32 before using this method.
357
358This will install the factory Atemio loader that is compatible with the AAF Recovery Tool (ART) to be able to install the Maxiuboot Loader.
359
360In order for this method to work make sure the setting Allow __"Iboot Update"__ is enabled in [wiki:Remote-Device-Control#point4.6 Iboot].
361
362When successfully achieved you may start up ART from your PC and install Maxiuboot.
363
364[[br]]
365
366Once installed you may set up your bootargs and change your Reseller ID back to its factory settings. For flashin original Firmware or other Software please refere to your receivers' manual or instructions.
367[[br]]
368[#point108.1 Top of Page]
369[[br]]
370
371----   
372'''8.14 Update TitanNit[=#point8.14] ([wiki:Wiki#point0 Contents]) ([WikiStart#point0 Main Page]) 
373----
374There are two ways to update your TitanNit version and there are merits to both methods :
375
376IRD offline method see [#point8 Installation / Recovery Inhaltsverzeichnis] and select your Reciever model to show information on how to update titan using an IRD titannit image.
377[[br]]
378''Note: using this method plugins and files stored to Flash will be formatted when the update is proformed.
379Plugins and files installed to MNT (except on the ufs 910/922) or a valid configured storage device will retain there settings .''
380
381Image Online Method see [wiki:System-Update#point3.5.7 System aktualisieren] for information on how preform an online update.
382[[br]]
383''Note: using this method all plugins and settings are retained as long as they are not installed in flash.''
384[[br]]
385[#point8 Top of Page]
386[[br]]
387
388----   
389'''8.15 IRD Download Locations'' [=#point8.15] ([wiki:Wiki#point0 Contents]) ([WikiStart#point0 Main Page]) 
390----
391* [wiki:Manufactures#point13 13 Manufactures] - [http://atemio.de/index.php/software-updates Stable Images][[br]] 
392* [wiki:Community#point14 14 Community] - [http://www.aaf-digital.info/forum/downloads.php?do=cat&id=2 Stable Images] [http://www.aaf-digital.info/forum/pages.php?pageid=12 Nightly Images][[br]] 
393 
394[[br]] 
395[#point8 Top of Page] 
396[[br]] 
Note: See TracBrowser for help on using the repository browser.