| 1 | ----
|
|---|
| 2 | '''8 Installation and Recovery Contents''' [=#point8] ([wiki:Wiki#point0 Contents]) ([WikiStart#point0 Main page])
|
|---|
| 3 | ----
|
|---|
| 4 |
|
|---|
| 5 | [[br]]
|
|---|
| 6 |
|
|---|
| 7 | This section contains information on installation and removal of TitanNit from your receiver
|
|---|
| 8 | [[br]]
|
|---|
| 9 | '''SH4 Models'''
|
|---|
| 10 |
|
|---|
| 11 | * [#point8.1 8.1 Atemio510 and compatible Models]
|
|---|
| 12 | * [#point8.2 8.2 Atemio520 and compatible Models]
|
|---|
| 13 | * [#point8.3 8.3 Atemio530 and compatible Models]
|
|---|
| 14 | * [#point8.4 8.4 Atemio7600 and compatible Models]
|
|---|
| 15 | * [#point8.5 8.5 Atemio700 and compatible Models]
|
|---|
| 16 | * [#point8.6 8.6 Atemio7000 and compatible Models]
|
|---|
| 17 | * [#point8.8 8.7 Ufs910]
|
|---|
| 18 | * [#point8.9 8.8 Ufs912]
|
|---|
| 19 | * [#point8.10 8.9 Ufs922]
|
|---|
| 20 |
|
|---|
| 21 | '''MIPS Models'''
|
|---|
| 22 |
|
|---|
| 23 | * [#point8.14 8.10 Atemio5000]
|
|---|
| 24 | * [#point8.15 8.11 Atemio5200]
|
|---|
| 25 |
|
|---|
| 26 | '''Aditional Info'''
|
|---|
| 27 |
|
|---|
| 28 | * [#point8.11 8.12 Installation on other Fortis Receivers]
|
|---|
| 29 | * [#point8.12 8.13 Uninstallation On other Fortis Receivers]
|
|---|
| 30 | * [#point8.13 8.14 Update TitanNit]
|
|---|
| 31 | * [#point8.14 8.15 IRD Download Location]
|
|---|
| 32 | [[br]]
|
|---|
| 33 | [[br]]
|
|---|
| 34 | [[br]]
|
|---|
| 35 |
|
|---|
| 36 |
|
|---|
| 37 | '''SH4 Models'''
|
|---|
| 38 | ----
|
|---|
| 39 | '''8.1 Atemio510''' [=#point8.1] ([wiki:Wiki#point0 Contents]) ([WikiStart#point0 Main page])
|
|---|
| 40 | ----
|
|---|
| 41 | '' How do I install an Atemio 510 IRD image? ''
|
|---|
| 42 | * Visit the Atemio homepage or the AAF digital forum and download the latest TitanNit firmware . ([#point8.15 IRD Download Locations])
|
|---|
| 43 | * Extract the zip file
|
|---|
| 44 | * Now copy the unzipped IRD firmware file to a formatted FAT32 USB stick.
|
|---|
| 45 | Note: The USB stick should not be formatted with windows. Use a separate program, such as the
|
|---|
| 46 | " HP USB Disk Storage Format Tool" (freeware program).
|
|---|
| 47 | Furthermore, we recommend a cheap USB stick with a small storage capacity as well as read and write speed.
|
|---|
| 48 | * Turn off the Receiver and disconnect all USB devices.
|
|---|
| 49 | * Connect the USB stick with the IRD file to your Receiver
|
|---|
| 50 | * Switch on (mains switch) and at the same time hold the CH + on the unit (about 15 seconds) until "search IRD File ... " appears,
|
|---|
| 51 | and the installation begins. Only then release the button
|
|---|
| 52 | Note: If installation does not start , use a different USB stick.
|
|---|
| 53 | * After successfully installing the receiver will reboot and the installed image should start-up
|
|---|
| 54 | [[br]]
|
|---|
| 55 | [#point8.1 Top of Page]
|
|---|
| 56 | [[br]]
|
|---|
| 57 |
|
|---|
| 58 | ----
|
|---|
| 59 | '''8.2 Atemio520''' [=#point8.2] ([wiki:Wiki#point0 Contents]) ([WikiStart#point0 Main page])
|
|---|
| 60 | ----
|
|---|
| 61 | '' How do I install an Atemio 520 IRD image? ''
|
|---|
| 62 | * Visit the Atemio homepage or the AAF digital forum and download the latest TitanNit firmware . ([#point8.15 IRD Download Locations])
|
|---|
| 63 | * Extract the zip file
|
|---|
| 64 | * Now copy the unzipped IRD firmware file to a formatted FAT32 USB stick.
|
|---|
| 65 | Note: The USB stick should not be formatted with windows. Use a separate program, such as the
|
|---|
| 66 | " HP USB Disk Storage Format Tool" (freeware program).
|
|---|
| 67 | Furthermore, we recommend a cheap USB stick with a small storage capacity as well as read and write speed.
|
|---|
| 68 | * Turn off the Receiver and disconnect all USB devices.
|
|---|
| 69 | * Connect the USB stick with the IRD file to your Receiver
|
|---|
| 70 | * Switch on (mains switch) and at the same time hold the CH + on the unit (about 15 seconds) until "search IRD File ... " appears,
|
|---|
| 71 | and the installation begins. Only then release the button
|
|---|
| 72 | Note: If installation does not start , use a different USB stick.
|
|---|
| 73 | * After successfully installing the receiver will reboot and the installed image should start-up
|
|---|
| 74 | [[br]]
|
|---|
| 75 | [#point8.1 Top of Page]
|
|---|
| 76 |
|
|---|
| 77 | ----
|
|---|
| 78 | '''8.3 Atemio530''' [=#point8.3] ([wiki:Wiki#point0 Contents]) ([WikiStart#point0 Main page])
|
|---|
| 79 | ----
|
|---|
| 80 | '' How do I install an Atemio 530 IRD image? ''
|
|---|
| 81 | * Visit the Atemio homepage or the AAF digital forum and download the latest TitanNit firmware . ([#point8.15 IRD Download Locations])
|
|---|
| 82 | * Extract the zip file
|
|---|
| 83 | * Now copy the unzipped IRD firmware file to a formatted FAT32 USB stick.
|
|---|
| 84 | Note: The USB stick should not be formatted with windows. Use a separate program, such as the
|
|---|
| 85 | " HP USB Disk Storage Format Tool" (freeware program).
|
|---|
| 86 | Furthermore, we recommend a cheap USB stick with a small storage capacity as well as read and write speed.
|
|---|
| 87 | * Turn off the Receiver and disconnect all USB devices.
|
|---|
| 88 | * Connect the USB stick with the IRD file to your Receiver
|
|---|
| 89 | * Switch on (mains switch) and at the same time hold the CH + on the unit (about 15 seconds) until "search IRD File ... " appears,
|
|---|
| 90 | and the installation begins. Only then release the button
|
|---|
| 91 | Note: If installation does not start , use a different USB stick.
|
|---|
| 92 | * After successfully installing the receiver will reboot and the installed image should start-up
|
|---|
| 93 | [[br]]
|
|---|
| 94 | [#point8.1 Top of Page]
|
|---|
| 95 | [[br]]
|
|---|
| 96 |
|
|---|
| 97 | ----
|
|---|
| 98 | '''8.4 Atemio7600''' [=#point8.4] ([wiki:Wiki#point0 Contents]) ([WikiStart#point0 Main page])
|
|---|
| 99 | ----
|
|---|
| 100 | '' How do I install an Atemio 7600 IRD image? ''
|
|---|
| 101 | * Visit the Atemio homepage or the AAF digital forum and download the latest TitanNit firmware . ([#point8.15 IRD Download Locations])
|
|---|
| 102 | * Extract the zip file
|
|---|
| 103 | * Now copy the unzipped IRD firmware file to a formatted FAT32 USB stick.
|
|---|
| 104 | Note: The USB stick should not be formatted with windows. Use a separate program, such as the
|
|---|
| 105 | " HP USB Disk Storage Format Tool" (freeware program).
|
|---|
| 106 | Furthermore, we recommend a cheap USB stick with a small storage capacity as well as read and write speed.
|
|---|
| 107 | * Turn off the Receiver and disconnect all USB devices.
|
|---|
| 108 | * Connect the USB stick with the IRD file to your Receiver
|
|---|
| 109 | * Switch on (mains switch) and at the same time hold the CH + on the unit (about 15 seconds) until "search IRD File ... " appears,
|
|---|
| 110 | and the installation begins. Only then release the button
|
|---|
| 111 | Note: If installation does not start , use a different USB stick.
|
|---|
| 112 | * After successfully installing the receiver will reboot and the installed image should start-up
|
|---|
| 113 | [[br]]
|
|---|
| 114 | [#point8.1 Top of Page]
|
|---|
| 115 | [[br]]
|
|---|
| 116 |
|
|---|
| 117 | ----
|
|---|
| 118 | '''8.5 Atevio700''' [=#point8.5] ([wiki:Wiki#point0 Contents]) ([WikiStart#point0 Main page])
|
|---|
| 119 | ----
|
|---|
| 120 | '' How do I install an Atemio 7600 IRD image? ''
|
|---|
| 121 | * Visit the Atemio homepage or the AAF digital forum and download the latest TitanNit firmware . ([#point8.15 IRD Download Locations])
|
|---|
| 122 | * Extract the zip file
|
|---|
| 123 | * Now copy the unzipped IRD firmware file to a formatted FAT32 USB stick.
|
|---|
| 124 | Note: The USB stick should not be formatted with windows. Use a separate program, such as the
|
|---|
| 125 | " HP USB Disk Storage Format Tool" (freeware program).
|
|---|
| 126 | Furthermore, we recommend a cheap USB stick with a small storage capacity as well as read and write speed.
|
|---|
| 127 | * Turn off the Receiver and disconnect all USB devices.
|
|---|
| 128 | * Connect the USB stick with the IRD file to your Receiver
|
|---|
| 129 | * Switch on (mains switch) and at the same time hold the CH + on the unit (about 15 seconds) until "search IRD File ... " appears,
|
|---|
| 130 | and the installation begins. Only then release the button
|
|---|
| 131 | Note: If installation does not start , use a different USB stick.
|
|---|
| 132 | * After successfully installing the receiver will reboot and the installed image should start-up
|
|---|
| 133 | [[br]]
|
|---|
| 134 | [#point8.1 Top of Page]
|
|---|
| 135 | [[br]]
|
|---|
| 136 |
|
|---|
| 137 | ----
|
|---|
| 138 | '''8.6 Atevio7000''' [=#point8.6] ([wiki:Wiki#point0 Contents]) ([WikiStart#point0 Main page])
|
|---|
| 139 | ----
|
|---|
| 140 | '' How do I install an Atemio 7000 IRD image? ''
|
|---|
| 141 | * Visit the Atemio homepage or the AAF digital forum and download the latest TitanNit firmware . ([#point8.15 IRD Download Locations])
|
|---|
| 142 | * Extract the zip file
|
|---|
| 143 | * Now copy the unzipped IRD firmware file to a formatted FAT32 USB stick.
|
|---|
| 144 | Note: The USB stick should not be formatted with windows. Use a separate program, such as the
|
|---|
| 145 | " HP USB Disk Storage Format Tool" (freeware program).
|
|---|
| 146 | Furthermore, we recommend a cheap USB stick with a small storage capacity as well as read and write speed.
|
|---|
| 147 | * Turn off the Receiver and disconnect all USB devices.
|
|---|
| 148 | * Connect the USB stick with the IRD file to your Receiver
|
|---|
| 149 | * Switch on (mains switch) and at the same time hold the CH + on the unit (about 15 seconds) until "search IRD File ... " appears,
|
|---|
| 150 | and the installation begins. Only then release the button
|
|---|
| 151 | Note: If installation does not start , use a different USB stick.
|
|---|
| 152 | * After successfully installing the receiver will reboot and the installed image should start-up
|
|---|
| 153 | [[br]]
|
|---|
| 154 | [#point8.1 Top of Page]
|
|---|
| 155 | [[br]]
|
|---|
| 156 |
|
|---|
| 157 | ----
|
|---|
| 158 | '''8.7 Kathrein Ufs910''' [=#point8.7] ([wiki:Wiki#point0 Contents]) ([WikiStart#point0 Main page])
|
|---|
| 159 | ----
|
|---|
| 160 | '' How do I install a Kathrein UFS910 update image? ''
|
|---|
| 161 | * When you install a USB .img file the mnt-filesystem is formatted. An Online Update leaves the mnt-filesystem untouched.
|
|---|
| 162 | * Visit the AAF digital forum and download the latest TitanNit firmware .
|
|---|
| 163 | * Extract the zip file
|
|---|
| 164 | * Now copy the unzipped img firmware file - must be renamed to miniFLASH.img - to a formatted FAT32 USB stick.
|
|---|
| 165 | Note: The USB stick should not be formatted with windows, but a separate program, such as the
|
|---|
| 166 | " HP USB Disk Storage Format Tool" (freeware program).
|
|---|
| 167 | Furthermore, we recommend a cheap USB stick with a small storage capacity as well as read and write speed.
|
|---|
| 168 | * Turn off the Receiver and disconnect all USB devices.
|
|---|
| 169 | * Connect the USB stick with the img file to the front USB Port
|
|---|
| 170 | * Switch on (mains switch) and at the same time hold the -Record button- on the Remote Control pressed (about 5 seconds)
|
|---|
| 171 | until "miniFLASH search..." appears, then the installation begins. Only then release the -Record button-
|
|---|
| 172 | Note: If installation does not start, use a different USB stick.
|
|---|
| 173 | * After successfully installing the receiver will reboot and the installed image should start-up
|
|---|
| 174 | [[br]]
|
|---|
| 175 | [#point8.1 Top of Page]
|
|---|
| 176 | [[br]]
|
|---|
| 177 |
|
|---|
| 178 | ----
|
|---|
| 179 | '''8.8 Kathrein UFS912''' [=#point8.8] ([wiki:Wiki#point0 Contents]) ([WikiStart#point0 Main page])
|
|---|
| 180 | ----
|
|---|
| 181 | '' How do I install a Kathrein UFS912 update image? ''
|
|---|
| 182 | * Visit the AAF digital forum and download the latest TitanNit firmware .
|
|---|
| 183 | * Extract the zip file
|
|---|
| 184 | * Now copy the unzipped firmware file *_FULL_nodebug.img to a formatted FAT32 USB stick into the path: /kathrein/ufs912/ .
|
|---|
| 185 | Note: The USB stick should not be formatted with windows, but a separate program, such as the
|
|---|
| 186 | " HP USB Disk Storage Format Tool" (freeware program).
|
|---|
| 187 | Furthermore, we recommend a cheap USB stick with a small storage capacity as well as read and write speed.
|
|---|
| 188 | * Turn off the Receiver and disconnect all USB devices.
|
|---|
| 189 | * Connect the USB stick with the img file
|
|---|
| 190 | * Switch on (mains switch) and at the same time press the -TV/Radio button- on the unit (about 5 seconds) until "emergency boot" appears,
|
|---|
| 191 | then the installation begins. Only after that message release the -TV/Radio button-
|
|---|
| 192 | Note: If installation does not start, use a different USB stick.
|
|---|
| 193 | * After successfully installing the receiver will reboot and the installed image should start-up
|
|---|
| 194 | [[br]]
|
|---|
| 195 | [#point8.1 Top of Page]
|
|---|
| 196 | [[br]]
|
|---|
| 197 |
|
|---|
| 198 | ----
|
|---|
| 199 | '''8.9 Kathrein UFS922''' [=#point8.9] ([wiki:Wiki#point0 Contents]) ([WikiStart#point0 Main page])
|
|---|
| 200 | ----
|
|---|
| 201 | '' How do I install a Kathrein UFS922 update image? ''
|
|---|
| 202 | * When you install a USB .img file the mnt-filesystem is formatted. An Online Update leaves the mnt-filesystem untouched.
|
|---|
| 203 | * Visit the AAF digital forum and download the latest TitanNit firmware .
|
|---|
| 204 | * Extract the zip file
|
|---|
| 205 | * Now copy the unzipped firmware file *_FULL_nodebug.img to a formatted FAT32 USB stick into the path: /kathrein/ufs922/ .
|
|---|
| 206 | Note: The USB stick should not be formatted with windows, but a separate program, such as the
|
|---|
| 207 | " HP USB Disk Storage Format Tool" (freeware program).
|
|---|
| 208 | Furthermore, we recommend a cheap USB stick with a small storage capacity as well as read and write speed.
|
|---|
| 209 | * Turn off the Receiver and disconnect all USB devices.
|
|---|
| 210 | * Connect the USB stick with the img file
|
|---|
| 211 | * Switch on (mains switch) and at the same time press the -TV/Radio button- on the unit (about 5 seconds) until "emergency boot" appears,
|
|---|
| 212 | then the installation begins. Only after that message release the -TV/Radio button-
|
|---|
| 213 | Note: If installation does not start, use a different USB stick.
|
|---|
| 214 | * After successfully installing the receiver will reboot and the installed image should start-up
|
|---|
| 215 | [[br]]
|
|---|
| 216 | [#point8.1 Top of Page]
|
|---|
| 217 | [[br]]
|
|---|
| 218 | [[br]]
|
|---|
| 219 | [[br]]
|
|---|
| 220 |
|
|---|
| 221 | '''Mips Models'''
|
|---|
| 222 | ----
|
|---|
| 223 | '''8.10 Atevio5000''' [=#point8.10] ([wiki:Wiki#point0 Contents]) ([WikiStart#point0 Main page])
|
|---|
| 224 | ----
|
|---|
| 225 | '' How do I install an Atemio 5000 Update UBI image? ''
|
|---|
| 226 | * Visit the Atemio homepage or the AAF digital forum and download the latest TitanNit firmware . ([#point8.15 IRD Download Locations])
|
|---|
| 227 | * Extract the zip file
|
|---|
| 228 | * Now copy the unzipped IRD firmware file to a formatted FAT32 USB stick.
|
|---|
| 229 | Note: After unpacking two subfolders atemio/5x00 will be created . The USB stick should not be formatted with windows. Use a separate program, such as the " HP USB Disk Storage Format Tool" (freeware program).
|
|---|
| 230 | Furthermore, we recommend a cheap USB stick with a small storage capacity as well as read and write speed.
|
|---|
| 231 | * Turn off the Receiver and disconnect all USB devices.
|
|---|
| 232 | * Connect the USB stick with the IRD file to your Receiver
|
|---|
| 233 | * Switch on ( mains plug ) and press the CH + on the unit (1 button from the right ) until the Vfd ( LCD Display) displayes " Flashing ...".
|
|---|
| 234 | then the installation begins, Only then release the button.
|
|---|
| 235 | Note: If installation does not start , use a different USB stick.
|
|---|
| 236 | * After successfully installing the receiver will reboot and the installed image should start-up
|
|---|
| 237 | [[br]]
|
|---|
| 238 | [#point8.1 Top of Page]
|
|---|
| 239 | [[br]]
|
|---|
| 240 |
|
|---|
| 241 | ----
|
|---|
| 242 | '''8.11 Atevio5200''' [=#point8.11] ([wiki:Wiki#point0 Contents]) ([WikiStart#point0 Main page])
|
|---|
| 243 | ----
|
|---|
| 244 | '' How do I install an Atemio 5200 Update UBI image? ''
|
|---|
| 245 | * Visit the Atemio homepage or the AAF digital forum and download the latest TitanNit firmware . ([#point8.15 IRD Download Locations])
|
|---|
| 246 | * Extract the zip file
|
|---|
| 247 | * Now copy the unzipped IRD firmware file to a formatted FAT32 USB stick.
|
|---|
| 248 | Note: After unpacking two subfolders atemio/5x00 will be created . The USB stick should not be formatted with windows. Use a separate program, such as the " HP USB Disk Storage Format Tool" (freeware program).
|
|---|
| 249 | Furthermore, we recommend a cheap USB stick with a small storage capacity as well as read and write speed.
|
|---|
| 250 | * Turn off the Receiver and disconnect all USB devices.
|
|---|
| 251 | * Connect the USB stick with the IRD file to your Receiver
|
|---|
| 252 | * Switch on ( mains plug ) and press the CH + on the unit (1 button from the right ) until the Vfd ( LCD Display) displayes " Flashing ...".
|
|---|
| 253 | then the installation begins, Only then release the button.
|
|---|
| 254 | Note: If installation does not start , use a different USB stick.
|
|---|
| 255 | * After successfully installing the receiver will reboot and the installed image should start-up
|
|---|
| 256 | [[br]]
|
|---|
| 257 | [#point8.1 Top of Page]
|
|---|
| 258 | [[br]]
|
|---|
| 259 | [[br]]
|
|---|
| 260 | [[br]]
|
|---|
| 261 |
|
|---|
| 262 |
|
|---|
| 263 | '''Aditional Info'''
|
|---|
| 264 | ----
|
|---|
| 265 | '''8.12 installation on other Fortis Receivers''' [=#point8.12] ([wiki:Wiki#point0 Contents]) ([WikiStart#point0 Main page])
|
|---|
| 266 | ----
|
|---|
| 267 | '''Installation Notes:'''
|
|---|
| 268 |
|
|---|
| 269 | ''If you wish to try or install titan you need to install an Atemio/Atevio factory loader. The original Atemio Bootloader has a security code within so an installation of Titan is not possible with any other fortis loader''
|
|---|
| 270 |
|
|---|
| 271 | ''If you wish to install Titan the loader version must be 1.54 or above. Titan versions above 1.32 require the new Iboot loader which needs to be installed first if not present.''
|
|---|
| 272 |
|
|---|
| 273 | ''There are various ways that are explained below:''
|
|---|
| 274 |
|
|---|
| 275 | [[br]]
|
|---|
| 276 |
|
|---|
| 277 | '''AAF Recovery Tool (ART) method'''
|
|---|
| 278 |
|
|---|
| 279 | * Install the AAF Recovery Tool (ART) and set up a connection to your receiver
|
|---|
| 280 | * Set the IP address and subnet mask of your uboot environment.
|
|---|
| 281 | * Reboot the receiver and reconnect to change the settings.
|
|---|
| 282 | * Install the factory loader and reboot.
|
|---|
| 283 | * The factory loader you installed is version 1.21 that you have to update to 1.54 to be compatible with Titan
|
|---|
| 284 | * Visit the [http:((www-atemio.de Atemio] homepage or the [http://www.aaf-digital.info/forum AAF digital forum] and download the latest Atevio/Atemio loaader (1.54).
|
|---|
| 285 | * Extract the zip file
|
|---|
| 286 | * Now copy the unzipped IRD firmware file to a formatted FAT32 USB stick.
|
|---|
| 287 | Note: The USB stick should not be formatted with windows. Use a separate program, such as the
|
|---|
| 288 | "HP USB Disk Storage Format Tool" (freeware program).
|
|---|
| 289 | Furthermore, we recommend a cheap USB stick with a small storage capacity as well as read and write speed.
|
|---|
| 290 | * Turn off the receiver and disconnect all USB devices.
|
|---|
| 291 | * Connect the USB stick with the IRD file to your receiver
|
|---|
| 292 | * Switch on (mains switch) and at the same time hold the CH + on the unit (about 15 seconds) until "search IRD File ... " appears,
|
|---|
| 293 | and the installation begins. Only then release the button
|
|---|
| 294 | Note: Should the installation not start, try a different USB stick.
|
|---|
| 295 | * Should you have installed the loader successfully the receiver will reboot and the installed Loader should start-up.
|
|---|
| 296 |
|
|---|
| 297 | ''You may now install Titan''
|
|---|
| 298 | [[br]]
|
|---|
| 299 |
|
|---|
| 300 |
|
|---|
| 301 | [[br]]
|
|---|
| 302 |
|
|---|
| 303 | '''Cross Flash Method'''
|
|---|
| 304 |
|
|---|
| 305 | ''This method explains how to install the HDF bootloader flash plugin to your fortis receiver and flash an Atemio/Atevio compatible bootloader from the plugin menu.''
|
|---|
| 306 |
|
|---|
| 307 | * Download the HDF Bootloader flash plugin from the [http://www.aaf-digital.info/forum AAF Digital forum].
|
|---|
| 308 | * Extract the zip file
|
|---|
| 309 | * Now copy the unzipped Plugin folder to a formatted FAT32 USB stick.
|
|---|
| 310 | Note: The USB stick should not be formatted with windows. Use a separate program, such as the
|
|---|
| 311 | " HP USB Disk Storage Format Tool" (freeware program).
|
|---|
| 312 | Furthermore, we recommend a cheap USB stick with a small storage capacity as well as read and write speed.
|
|---|
| 313 | * go to the plugins section in your receiver and install the plugin and then start it.
|
|---|
| 314 | * type in the password contained in the zip file and follow the onscreen prompts.
|
|---|
| 315 | * Should you have installed the loader successfully the receiver will reboot and the installed Loader should start-up.
|
|---|
| 316 |
|
|---|
| 317 | ''You may now install TitanNit''
|
|---|
| 318 |
|
|---|
| 319 | [[br]]
|
|---|
| 320 |
|
|---|
| 321 | '''Reseller Changer Tool Method'''
|
|---|
| 322 |
|
|---|
| 323 | ''This method explains how to change the Reseler ID of an Atemio/Atevio compatible bootloader and flash it to any compatible Fortis receiver from the plugin menu.''
|
|---|
| 324 |
|
|---|
| 325 |
|
|---|
| 326 | * Visit the [http://www.atemio.de Atemio] homepage or the [http://www.aaf-digital.info/forum AAF digital forum] and download the latest Atevio/Atemio loader.
|
|---|
| 327 | * Extract the zip file
|
|---|
| 328 | * use the reseller ID changer tool and change the IRD to that of your reseller ID.
|
|---|
| 329 | * Now copy the unzipped IRD firmware file to a formatted FAT32 USB stick.
|
|---|
| 330 | Note: The USB stick should not be formatted with windows. Use a separate program, such as the
|
|---|
| 331 | " HP USB Disk Storage Format Tool" (freeware program).
|
|---|
| 332 | Furthermore, we recommend a cheap USB stick with a small storage capacity as well as read and write speed.
|
|---|
| 333 | * Turn off the Receiver and disconnect all USB devices.
|
|---|
| 334 | * Connect the USB stick with the IRD file to your Receiver.
|
|---|
| 335 | * Switch on (mains switch) and at the same time hold the CH + on the unit (about 15 seconds) until "search IRD File ... " appears,
|
|---|
| 336 | and the installation begins. Only then release the button
|
|---|
| 337 | Note: If installation does not start , use a different USB stick.
|
|---|
| 338 | * Should you have installed the loader successfully the receiver will reboot and the installed Loader should start-up.
|
|---|
| 339 |
|
|---|
| 340 |
|
|---|
| 341 | This method requires you to also change the reseller ID to be able to install TitanNit.
|
|---|
| 342 |
|
|---|
| 343 |
|
|---|
| 344 | '''Be aware should it the installation fail or a loss of Power occur during the flashing process you could brick your receiver as there is no recovery method. Compatibility with other receivers is not guaranteed but you may find a list of compatible receivers in the [wiki:Supported-Receivers#point7 Supported Receivers] section.'''
|
|---|
| 345 | [[br]]
|
|---|
| 346 | [#point8.1 Top of Page]
|
|---|
| 347 | ----
|
|---|
| 348 | '''8.13 Uninstalling Titan''' [=#point8.13] ([wiki:Wiki#point0 Contents]) ([WikiStart#point0 Main page])
|
|---|
| 349 | ----
|
|---|
| 350 | If you have an Atemio/Atevio or UFS receiver all you have to do is install your original ird file as explained above and no bootloader changes are neccessary.
|
|---|
| 351 |
|
|---|
| 352 | Uninstalling titan and switching back to the original reseller loader can't be done (easily) for other fortis receivers but there is one simple alternative method outlined below.
|
|---|
| 353 |
|
|---|
| 354 |
|
|---|
| 355 | '''Uninstalling Titan on non Atemio/Atevio receiver and restore Reseller ID with Maxi-uboot'''
|
|---|
| 356 |
|
|---|
| 357 | If you have iboot installed then you must install a version of TitanNit older than 1.32 before using this method.
|
|---|
| 358 |
|
|---|
| 359 | This will install the factory Atemio loader that is compatible with the AAF Recovery Tool (ART) to be able to install the Maxiuboot Loader.
|
|---|
| 360 |
|
|---|
| 361 | In order for this method to work make sure the setting Allow __"Iboot Update"__ is enabled in [wiki:Remote-Device-Control#point4.6 Iboot].
|
|---|
| 362 |
|
|---|
| 363 | When successfully achieved you may start up ART from your PC and install Maxiuboot.
|
|---|
| 364 |
|
|---|
| 365 | [[br]]
|
|---|
| 366 |
|
|---|
| 367 | Once installed you may set up your bootargs and change your Reseller ID back to its factory settings. For flashin original Firmware or other Software please refere to your receivers' manual or instructions.
|
|---|
| 368 | [[br]]
|
|---|
| 369 | [#point108.1 Top of Page]
|
|---|
| 370 | [[br]]
|
|---|
| 371 |
|
|---|
| 372 | ----
|
|---|
| 373 | '''8.14 Update TitanNit''' [=#point8.14] ([wiki:Wiki#point0 Contents]) ([WikiStart#point0 Main Page])
|
|---|
| 374 | ----
|
|---|
| 375 | There are two ways to update your TitanNit version and there are merits to both methods :
|
|---|
| 376 |
|
|---|
| 377 | IRD offline method see [#point8 Installation / Recovery Inhaltsverzeichnis] and select your Reciever model to show information on how to update titan using an IRD titannit image.
|
|---|
| 378 | [[br]]
|
|---|
| 379 | ''Note: using this method plugins and files stored to Flash will be formatted when the update is proformed.
|
|---|
| 380 | Plugins and files installed to MNT (except on the ufs 910/922) or a valid configured storage device will retain there settings .''
|
|---|
| 381 |
|
|---|
| 382 | Image Online Method see [wiki:System-Update#point3.5.7 System aktualisieren] for information on how preform an online update.
|
|---|
| 383 | [[br]]
|
|---|
| 384 | ''Note: using this method all plugins and settings are retained as long as they are not installed in flash.''
|
|---|
| 385 | [[br]]
|
|---|
| 386 | [#point8 Top of Page]
|
|---|
| 387 | [[br]]
|
|---|
| 388 |
|
|---|
| 389 | ----
|
|---|
| 390 | '''8.15 IRD Download Locations''' [=#point8.15] ([wiki:Wiki#point0 Contents]) ([WikiStart#point0 Main Page])
|
|---|
| 391 | ----
|
|---|
| 392 | * [wiki:Manufactures#point13 13 Manufactures] - [http://atemio.de/index.php/software-updates Stable Images][[br]]
|
|---|
| 393 | * [wiki:Community#point14 14 Community] - [http://www.aaf-digital.info/forum/downloads.php?do=cat&id=2 Stable Images] [http://www.aaf-digital.info/forum/pages.php?pageid=12 Nightly Images][[br]]
|
|---|
| 394 |
|
|---|
| 395 | [[br]]
|
|---|
| 396 | [#point8 Top of Page]
|
|---|
| 397 | [[br]]
|
|---|
