source: wiki/pages/ru/Installation-Recovery @ 37372

Last change on this file since 37372 was 37372, checked in by aafsvn, 8 years ago

[titan] autoupdate wiki files

File size: 19.1 KB
Line 
1----
2'''8 Installation and Recovery Contents''' [=#point8] ([wiki:Wiki#point0 Contents]) ([WikiStart#point0 Main page])
3----
4
5[[br]]
6
7This section contains information on installation and removal of TitanNit from your receiver
8
9[[br]]
10
11 * [#point8.1 8.1 Atemio510 and compatible Models]
12 * [#point8.2 8.2 Atemio520 and compatible Models]
13 * [#point8.3 8.3 Atemio530 and compatible Models]
14 * [#point8.4 8.4 Atemio7600 and compatible Models]
15 * [#point8.5 8.5 Atemio700 and compatible Models]
16 * [#point8.6 8.6 Atemio7000 and compatible Models]
17 * [#point8.7 8.7 Ufs910]
18 * [#point8.8 8.8 Ufs912]
19 * [#point8.9 8.9 Ufs922]
20 * [#point8.10 8.10 Installation on other Fortis Receivers]
21 * [#point8.11 8.11 Uninstallation On other Fortis Receivers]
22 * [#point8.12 8.12 Update TitanNit]
23 * [#point8.13 8.13 IRD Download Location]
24
25
26[[br]]
27
28
29----
30'''8.1 Atemio510''' [=#point8.1] ([wiki:Wiki#point0 Contents]) ([WikiStart#point0 Main page])
31----
32
33[[br]]
34
35'' How do I install an Atemio 510 IRD image? ''
36 * Visit the Atemio homepage or the AAF digital forum and download the latest TitanNit firmware .
37 * Extract the zip file
38 * Now copy the unzipped IRD firmware file to a formatted FAT32 USB stick.
39     Note: The USB stick should not be formatted with windows. Use a separate program, such as the
40     " HP USB Disk Storage Format Tool" (freeware program).
41     Furthermore, we recommend a cheap USB stick with a small storage capacity as well as read and write speed.
42 * Turn off the Receiver and disconnect all USB devices.
43 * Connect the USB stick with the IRD file to your Receiver
44 * Switch on (mains switch) and at the same time hold the CH + on the unit (about 15 seconds) until "search IRD File ... " appears,
45   and the installation begins. Only then release the button
46     Note: If installation does not start , use a different USB stick.
47 * After successfully installing the receiver will reboot and the installed image should start-up
48[[br]]
49[#point8.1 Top of Page]
50----
51'''8.2 Atemio520''' [=#point8.2] ([wiki:Wiki#point0 Contents]) ([WikiStart#point0 Main page])
52----
53
54[[br]]
55
56'' How do I install an Atemio 520 IRD image? ''
57 * Visit the Atemio homepage or the AAF digital forum and download the latest TitanNit firmware .
58 * Extract the zip file
59 * Now copy the unzipped IRD firmware file to a formatted FAT32 USB stick.
60     Note: The USB stick should not be formatted with windows. Use a separate program, such as the
61     " HP USB Disk Storage Format Tool" (freeware program).
62     Furthermore, we recommend a cheap USB stick with a small storage capacity as well as read and write speed.
63 * Turn off the Receiver and disconnect all USB devices.
64 * Connect the USB stick with the IRD file to your Receiver
65 * Switch on (mains switch) and at the same time hold the CH + on the unit (about 15 seconds) until "search IRD File ... " appears,
66   and the installation begins. Only then release the button
67     Note: If installation does not start , use a different USB stick.
68 * After successfully installing the receiver will reboot and the installed image should start-up
69[[br]]
70[#point8.1 Top of Page]
71
72----
73'''8.3 Atemio530''' [=#point8.3] ([wiki:Wiki#point0 Contents]) ([WikiStart#point0 Main page])
74----
75
76[[br]]
77'' How do I install an Atemio 530 IRD image? ''
78 * Visit the Atemio homepage or the AAF digital forum and download the latest TitanNit firmware .
79 * Extract the zip file
80 * Now copy the unzipped IRD firmware file to a formatted FAT32 USB stick.
81     Note: The USB stick should not be formatted with windows. Use a separate program, such as the
82     " HP USB Disk Storage Format Tool" (freeware program).
83     Furthermore, we recommend a cheap USB stick with a small storage capacity as well as read and write speed.
84 * Turn off the Receiver and disconnect all USB devices.
85 * Connect the USB stick with the IRD file to your Receiver
86 * Switch on (mains switch) and at the same time hold the CH + on the unit (about 15 seconds) until "search IRD File ... " appears,
87   and the installation begins. Only then release the button
88     Note: If installation does not start , use a different USB stick.
89 * After successfully installing the receiver will reboot and the installed image should start-up
90[[br]]
91[#point8.1 Top of Page]
92
93----
94'''8.4 Atemio7600''' [=#point8.4] ([wiki:Wiki#point0 Contents]) ([WikiStart#point0 Main page])
95----
96
97[[br]]
98'' How do I install an Atemio 7600 IRD image? ''
99 * Visit the Atemio homepage or the AAF digital forum and download the latest TitanNit firmware .
100 * Extract the zip file
101 * Now copy the unzipped IRD firmware file to a formatted FAT32 USB stick.
102     Note: The USB stick should not be formatted with windows. Use a separate program, such as the
103     " HP USB Disk Storage Format Tool" (freeware program).
104     Furthermore, we recommend a cheap USB stick with a small storage capacity as well as read and write speed.
105 * Turn off the Receiver and disconnect all USB devices.
106 * Connect the USB stick with the IRD file to your Receiver
107 * Switch on (mains switch) and at the same time hold the CH + on the unit (about 15 seconds) until "search IRD File ... " appears,
108   and the installation begins. Only then release the button
109     Note: If installation does not start , use a different USB stick.
110 * After successfully installing the receiver will reboot and the installed image should start-up
111[[br]]
112[#point8.1 Top of Page]
113
114----
115'''8.5 Atevio700''' [=#point8.5] ([wiki:Wiki#point0 Contents]) ([WikiStart#point0 Main page])
116----
117
118[[br]]
119
120'' How do I install an Atemio 700 IRD image? ''
121 * Visit the Atemio homepage or the AAF digital forum and download the latest TitanNit firmware .
122 * Extract the zip file
123 * Now copy the unzipped IRD firmware file to a formatted FAT32 USB stick.
124     Note: The USB stick should not be formatted with windows. Use a separate program, such as the
125     " HP USB Disk Storage Format Tool" (freeware program).
126     Furthermore, we recommend a cheap USB stick with a small storage capacity as well as read and write speed.
127 * Turn off the Receiver and disconnect all USB devices.
128 * Connect the USB stick with the IRD file to your Receiver
129 * Switch on (mains switch) and at the same time hold the CH + on the unit (about 15 seconds) until "search IRD File ... " appears,
130   and the installation begins. Only then release the button
131     Note: If installation does not start , use a different USB stick.
132 * After successfully installing the receiver will reboot and the installed image should start-up
133[[br]]
134[#point8.1 Top of Page]
135
136----
137'''8.6 Atevio7000''' [=#point8.6] ([wiki:Wiki#point0 Contents]) ([WikiStart#point0 Main page])
138----
139
140[[br]]
141
142'' How do I install an Atemio 7000 IRD image? ''
143 * Visit the Atemio homepage or the AAF digital forum and download the latest TitanNit firmware .
144 * Extract the zip file
145 * Now copy the unzipped IRD firmware file to a formatted FAT32 USB stick.
146     Note: The USB stick should not be formatted with windows. Use a separate program, such as the
147     " HP USB Disk Storage Format Tool" (freeware program).
148     Furthermore, we recommend a cheap USB stick with a small storage capacity as well as read and write speed.
149 * Turn off the Receiver and disconnect all USB devices.
150 * Connect the USB stick with the IRD file to your Receiver
151 * Switch on (mains switch) and at the same time hold the CH + on the unit (about 15 seconds) until "search IRD File ... " appears,
152   and the installation begins. Only then release the button
153     Note: If installation does not start , use a different USB stick.
154 * After successfully installing the receiver will reboot and the installed image should start-up
155[[br]]
156[#point8.1 Top of Page]
157
158----
159'''8.7 Kathrein Ufs910''' [=#point8.7] ([wiki:Wiki#point0 Contents]) ([WikiStart#point0 Main page])
160----
161
162[[br]]
163
164'' How do I install a Kathrein UFS910 update image? ''
165 * When you install a USB .img file the mnt-filesystem is formatted. An Online Update leaves the mnt-filesystem untouched.
166 * Visit the AAF digital forum and download the latest TitanNit firmware .
167 * Extract the zip file
168 * Now copy the unzipped img firmware file - must be renamed to miniFLASH.img - to a formatted FAT32 USB stick.
169     Note: The USB stick should not be formatted with windows, but a separate program, such as the
170     " HP USB Disk Storage Format Tool" (freeware program).
171     Furthermore, we recommend a cheap USB stick with a small storage capacity as well as read and write speed.
172 * Turn off the Receiver and disconnect all USB devices.
173 * Connect the USB stick with the img file to the front USB Port
174 * Switch on (mains switch) and at the same time hold the -Record button- on the Remote Control pressed (about 5 seconds)
175   until "miniFLASH search..." appears, then the installation begins. Only then release the -Record button-
176     Note: If installation does not start, use a different USB stick.
177 * After successfully installing the receiver will reboot and the installed image should start-up
178[[br]]
179[#point8.1 Top of Page]
180
181----
182'''8.8 Kathrein UFS912''' [=#point8.8] ([wiki:Wiki#point0 Contents]) ([WikiStart#point0 Main page])
183----
184
185[[br]]
186
187'' How do I install a Kathrein UFS912 update image? ''
188 * Visit the AAF digital forum and download the latest TitanNit firmware .
189 * Extract the zip file
190 * Now copy the unzipped firmware file *_FULL_nodebug.img to a formatted FAT32 USB stick into the path: /kathrein/ufs912/ .
191     Note: The USB stick should not be formatted with windows, but a separate program, such as the
192     " HP USB Disk Storage Format Tool" (freeware program).
193     Furthermore, we recommend a cheap USB stick with a small storage capacity as well as read and write speed.
194 * Turn off the Receiver and disconnect all USB devices.
195 * Connect the USB stick with the img file
196 * Switch on (mains switch) and at the same time press the -TV/Radio button- on the unit (about 5 seconds) until "emergency boot" appears,
197   then the installation begins. Only after that message release the -TV/Radio button-
198     Note: If installation does not start, use a different USB stick.
199 * After successfully installing the receiver will reboot and the installed image should start-up
200[[br]]
201[#point8.1 Top of Page]
202
203----
204'''8.9 Kathrein UFS922''' [=#point8.9] ([wiki:Wiki#point0 Contents]) ([WikiStart#point0 Main page])
205----
206
207[[br]]
208
209'' How do I install a Kathrein UFS922 update image? ''
210 * When you install a USB .img file the mnt-filesystem is formatted. An Online Update leaves the mnt-filesystem untouched.
211 * Visit the AAF digital forum and download the latest TitanNit firmware .
212 * Extract the zip file
213 * Now copy the unzipped firmware file *_FULL_nodebug.img to a formatted FAT32 USB stick into the path: /kathrein/ufs922/ .
214     Note: The USB stick should not be formatted with windows, but a separate program, such as the
215     " HP USB Disk Storage Format Tool" (freeware program).
216     Furthermore, we recommend a cheap USB stick with a small storage capacity as well as read and write speed.
217 * Turn off the Receiver and disconnect all USB devices.
218 * Connect the USB stick with the img file
219 * Switch on (mains switch) and at the same time press the -TV/Radio button- on the unit (about 5 seconds) until "emergency boot" appears,
220   then the installation begins. Only after that message release the -TV/Radio button-
221     Note: If installation does not start, use a different USB stick.
222 * After successfully installing the receiver will reboot and the installed image should start-up
223[[br]]
224[#point8.1 Top of Page]
225
226
227----
228'''installation on other Fortis Receivers'''  [=#point8.10] ([wiki:Wiki#point0 Contents]) ([WikiStart#point0 Main page])
229----
230
231[[br]]
232
233'''Installation Notes:'''
234
235''If you wish to try or install titan you need to install an Atemio/Atevio factory loader. The original Atemio Bootloader has a security code within so an installation of Titan is not possible with any other fortis loader''
236
237''If you wish to install Titan the loader version must be 1.54 or above. Titan versions above 1.32 require the new Iboot loader which needs to be installed first if not present.''
238
239''There are various ways that are explained below:''
240 
241[[br]]
242
243'''AAF Recovery Tool (ART) method'''
244
245 * Install the AAF Recovery Tool (ART) and set up a connection to your receiver
246 * Set the IP address and subnet mask of your uboot environment.
247 * Reboot the receiver and reconnect to change the settings.
248 * Install the factory loader and reboot.
249 * The factory loader you installed is version 1.21 that you have to update to 1.54 to be compatible with Titan
250 * Visit the [http:((www-atemio.de Atemio] homepage or the [http://www.aaf-digital.info/forum AAF digital forum] and download the latest Atevio/Atemio loaader (1.54).
251 * Extract the zip file
252  * Now copy the unzipped IRD firmware file to a formatted FAT32 USB stick.
253     Note: The USB stick should not be formatted with windows. Use a separate program, such as the
254     "HP USB Disk Storage Format Tool" (freeware program).
255     Furthermore, we recommend a cheap USB stick with a small storage capacity as well as read and write speed.
256 * Turn off the receiver and disconnect all USB devices.
257 * Connect the USB stick with the IRD file to your receiver
258 * Switch on (mains switch) and at the same time hold the CH + on the unit (about 15 seconds) until "search IRD File ... " appears,
259   and the installation begins. Only then release the button
260     Note: Should the installation not start, try a different USB stick.
261 * Should you have installed the loader successfully the receiver will reboot and the installed Loader should start-up.
262
263''You may now install Titan''
264[[br]]
265
266
267[[br]]
268
269'''Cross Flash Method'''
270
271''This method explains how to install the HDF bootloader flash plugin to your fortis receiver and flash an Atemio/Atevio compatible bootloader from the plugin menu.''
272
273* Download the HDF Bootloader flash plugin from the [http://www.aaf-digital.info/forum AAF Digital forum].
274 * Extract the zip file
275 * Now copy the unzipped Plugin folder to a formatted FAT32 USB stick.
276     Note: The USB stick should not be formatted with windows. Use a separate program, such as the
277     " HP USB Disk Storage Format Tool" (freeware program).
278     Furthermore, we recommend a cheap USB stick with a small storage capacity as well as read and write speed.
279 * go to the plugins section in your receiver and install the plugin and then start it.
280 * type in the password contained in the zip file and follow the onscreen prompts.
281 * Should you have installed the loader successfully the receiver will reboot and the installed Loader should start-up.
282
283''You may now install TitanNit''
284
285[[br]]
286
287'''Reseller Changer Tool Method'''
288
289''This method explains how to change the Reseler ID of an Atemio/Atevio compatible bootloader and flash it to any compatible Fortis receiver from the plugin menu.''
290
291
292* Visit the [http://www.atemio.de Atemio] homepage or the [http://www.aaf-digital.info/forum AAF digital forum] and download the latest Atevio/Atemio loader.
293 * Extract the zip file
294 * use the reseller ID changer tool and change the IRD to that of your reseller ID.
295 * Now copy the unzipped IRD firmware file to a formatted FAT32 USB stick.
296     Note: The USB stick should not be formatted with windows. Use a separate program, such as the
297     " HP USB Disk Storage Format Tool" (freeware program).
298     Furthermore, we recommend a cheap USB stick with a small storage capacity as well as read and write speed.
299 * Turn off the Receiver and disconnect all USB devices.
300 * Connect the USB stick with the IRD file to your Receiver.
301 * Switch on (mains switch) and at the same time hold the CH + on the unit (about 15 seconds) until "search IRD File ... " appears,
302   and the installation begins. Only then release the button
303     Note: If installation does not start , use a different USB stick.
304 * Should you have installed the loader successfully the receiver will reboot and the installed Loader should start-up.
305
306
307This method requires you to also change the reseller ID to be able to install TitanNit.
308
309
310'''Be aware should it the installation fail or a loss of Power occur during the flashing process you could brick your receiver as there is no recovery method. Compatibility with other receivers is not guaranteed but you may find a list of compatible receivers in the [wiki:Supported-Receivers#point7 Supported Receivers] section.'''
311[[br]]
312[#point8.1 Top of Page]
313----
314'''8.11 Uninstalling Titan'' [=#point8.11] ([wiki:Wiki#point0 Contents]) ([WikiStart#point0 Main page])
315----
316[[br]]
317
318If you have an Atemio/Atevio or UFS receiver all you have to do is install your original ird file as explained above and no bootloader changes are neccessary.
319
320Uninstalling titan and switching back to the original reseller loader can't be done (easily) for other fortis receivers but there is one simple alternative method outlined below.
321
322
323'''Uninstalling Titan on non Atemio/Atevio receiver and restore Reseller ID with Maxi-uboot'''
324
325If you have iboot installed then you must install a version of TitanNit older than 1.32 before using this method.
326
327This will install the factory Atemio loader that is compatible with the AAF Recovery Tool (ART) to be able to install the Maxiuboot Loader.
328
329In order for this method to work make sure the setting Allow __"Iboot Update"__ is enabled in [wiki:Remote-Device-Control#point4.6 Iboot].
330
331When successfully achieved you may start up ART from your PC and install Maxiuboot.
332
333[[br]]
334
335Once installed you may set up your bootargs and change your Reseller ID back to its factory settings. For flashin original Firmware or other Software please refere to your receivers' manual or instructions.
336[[br]]
337[#point108.1 Top of Page]
338
339
340----   
341'''8.13 Update TitanNit[=#point8.12] ([wiki:Wiki#point0 Contents]) ([WikiStart#point0 Main Page]) 
342---- 
343[[br]] 
344
345There are two ways to update your TitanNit version and there are merits to both methods :
346
347IRD offline method see [#point8 Installation / Recovery Inhaltsverzeichnis] and select your Reciever model to show information on how to update titan using an IRD titannit image.
348[[br]]
349''Note: using this method plugins and files stored to Flash will be formatted when the update is proformed.
350Plugins and files installed to MNT (except on the ufs 910/922) or a valid configured storage device will retain there settings .''
351
352Image Online Method see [wiki:System-Update#point3.5.7 System aktualisieren] for information on how preform an online update.
353[[br]]
354''Note: using this method all plugins and settings are retained as long as they are not installed in flash.''
355
356[[br]]
357
358[#point8 Top of Page]
359
360[[br]]
361
362----   
363'''8.13 IRD Download Locations'' [=#point8.13] ([wiki:Wiki#point0 Contents]) ([WikiStart#point0 Main Page]) 
364---- 
365[[br]] 
366
367* [wiki:Manufactures#point13 13 Manufactures] - [http://atemio.de/index.php/software-updates Stable Images][[br]] 
368* [wiki:Community#point14 14 Community] - [http://www.aaf-digital.info/forum/downloads.php?do=cat&id=2 Stable Images] [http://www.aaf-digital.info/forum/pages.php?pageid=12 Nightly Images][[br]] 
369 
370[[br]] 
371[#point8 Top of Page] 
372[[br]] 
373[[br]] 
374[[br]]
Note: See TracBrowser for help on using the repository browser.