Ignore:
Timestamp:
03/12/17 13:01:59 (7 years ago)
Author:
obi
Message:

reset wiki

File:
1 edited

Legend:

Unmodified
Added
Removed
  • wiki/pages/pl/Installation-Recovery-SH4-Atemio

    r40228 r40231  
     1[[TranslatedPages]]
     2----
     3'''SH4 Atemio (Atevio)'''[=#point8.00]
     4----
     5
     6The SH4 Atemio recievers are manufactured by Fortis who are a Korean manufacturer of satellite receivers all atemio (atevio) models are compatible with TitanNit.
     7as TitanNit was developed for these recievers no bootloader software ID changes are required to install TitanNit, some of these models cam factory supplied with TitanNit such as the atemio  530.
     8
     9'''SH4 Atemio Contents'''
     10
     11 * [#point8.001 8.001 Atemio510]
     12 * [#point8.002 8.002 Atemio520]
     13 * [#point8.003 8.003 Atemio530]
     14 * [#point8.004 8.004 Atemio7600]
     15 * [#point8.005 8.005 Atevio700]
     16 * [#point8.006 8.006 Atevio7000]
     17
     18'''Additional Info'''
     19
     20 * [#point8.007 8.007 Uninstallation]
     21 * [#point8.008 8.008 Update TitanNit]
     22 * [#point8.009 8.009 IRD Download Location]
     23
     24
     25
     26----
     27'''8.1 Atemio510 and Fortis HS-7810''' [=#point8.001] ([wiki:Wiki#point0 Contents]) ([WikiStart#point0 Main page])
     28----
     29'' How do I install an Atemio 510 IRD image? ''
     30 * Visit the Atemio homepage or the AAF digital forum and download the latest TitanNit firmware . ([#point8.15 IRD Download Locations])
     31 * Extract the zip file
     32 * Now copy the unzipped IRD firmware file to a formatted FAT32 USB stick.
     33     Note: The USB stick should not be formatted with windows. Use a separate program, such as the
     34     " HP USB Disk Storage Format Tool" (freeware program).
     35     Furthermore, we recommend a cheap USB stick with a small storage capacity as well as read and write speed.
     36 * Turn off the Receiver and disconnect all USB devices.
     37 * Connect the USB stick with the IRD file to your Receiver
     38 * Switch on (mains switch) and at the same time hold the CH + on the unit (about 15 seconds) until "search IRD File ... " appears,
     39   and the installation begins. Only then release the button
     40     Note: If installation does not start , use a different USB stick.
     41 * After successfully installing the receiver will reboot and the installed image should start-up
     42[[br]]
     43  '''[wiki:Remote-Device-Control#point4.6 4.6 Bootloader sh4 Boxen]'''[[br]]
     44* [http://sbnc.dyndns.tv/trac/wiki/en/Remote-Device-Control#point4.6  iboot sh4 loader flashing and recovery ][[br]] 
     45[#point8 Top of Page]
     46[[br]]
     47----
     48'''8.2 Atemio520''' [=#point8.002] ([wiki:Wiki#point0 Contents]) ([WikiStart#point0 Main page])
     49----
     50'' How do I install an Atemio 520 IRD image? ''
     51 * Visit the Atemio homepage or the AAF digital forum and download the latest TitanNit firmware . ([#point8.15 IRD Download Locations])
     52 * Extract the zip file
     53 * Now copy the unzipped IRD firmware file to a formatted FAT32 USB stick.
     54     Note: The USB stick should not be formatted with windows. Use a separate program, such as the
     55     " HP USB Disk Storage Format Tool" (freeware program).
     56     Furthermore, we recommend a cheap USB stick with a small storage capacity as well as read and write speed.
     57 * Turn off the Receiver and disconnect all USB devices.
     58 * Connect the USB stick with the IRD file to your Receiver
     59 * Switch on (mains switch) and at the same time hold the CH + on the unit (about 15 seconds) until "search IRD File ... " appears,
     60   and the installation begins. Only then release the button
     61     Note: If installation does not start , use a different USB stick.
     62 * After successfully installing the receiver will reboot and the installed image should start-up
     63[[br]]
     64  '''[wiki:Remote-Device-Control#point4.6 4.6 Bootloader sh4 Boxen]'''[[br]]
     65* [http://sbnc.dyndns.tv/trac/wiki/en/Remote-Device-Control#point4.6  iboot sh4 loader flashing and recovery ][[br]] 
     66[#point8 Top of Page]
     67[[br]]
     68----
     69'''8.3 Atemio530''' [=#point8.003] ([wiki:Wiki#point0 Contents]) ([WikiStart#point0 Main page])
     70----
     71'' How do I install an Atemio 530 IRD image? ''
     72 * Visit the Atemio homepage or the AAF digital forum and download the latest TitanNit firmware . ([#point8.15 IRD Download Locations])
     73 * Extract the zip file
     74 * Now copy the unzipped IRD firmware file to a formatted FAT32 USB stick.
     75     Note: The USB stick should not be formatted with windows. Use a separate program, such as the
     76     " HP USB Disk Storage Format Tool" (freeware program).
     77     Furthermore, we recommend a cheap USB stick with a small storage capacity as well as read and write speed.
     78 * Turn off the Receiver and disconnect all USB devices.
     79 * Connect the USB stick with the IRD file to your Receiver
     80 * Switch on (mains switch) and at the same time hold the CH + on the unit (about 15 seconds) until "search IRD File ... " appears,
     81   and the installation begins. Only then release the button
     82     Note: If installation does not start , use a different USB stick.
     83 * After successfully installing the receiver will reboot and the installed image should start-up
     84[[br]]
     85[#point8 Top of Page]
     86[[br]]
     87----
     88'''8.4 Atemio7600 and Fortis HX-8200''' [=#point8.004] ([wiki:Wiki#point0 Contents]) ([WikiStart#point0 Main page])
     89----
     90'' How do I install an Atemio 7600 IRD image? ''
     91 * Visit the Atemio homepage or the AAF digital forum and download the latest TitanNit firmware . ([#point8.15 IRD Download Locations])
     92 * Extract the zip file
     93 * Now copy the unzipped IRD firmware file to a formatted FAT32 USB stick.
     94     Note: The USB stick should not be formatted with windows. Use a separate program, such as the
     95     " HP USB Disk Storage Format Tool" (freeware program).
     96     Furthermore, we recommend a cheap USB stick with a small storage capacity as well as read and write speed.
     97 * Turn off the Receiver and disconnect all USB devices.
     98 * Connect the USB stick with the IRD file to your Receiver
     99 * Switch on (mains switch) and at the same time hold the CH + on the unit (about 15 seconds) until "search IRD File ... " appears,
     100   and the installation begins. Only then release the button
     101     Note: If installation does not start , use a different USB stick.
     102 * After successfully installing the receiver will reboot and the installed image should start-up
     103[[br]]
     104  '''[wiki:Remote-Device-Control#point4.6 4.6 Bootloader sh4 Boxen]'''[[br]]
     105* [http://sbnc.dyndns.tv/trac/wiki/en/Remote-Device-Control#point4.6  iboot sh4 loader flashing and recovery ][[br]] 
     106[#point8 Top of Page]
     107[[br]]
     108----
     109'''8.5 Atevio700''' [=#point8.005] ([wiki:Wiki#point0 Contents]) ([WikiStart#point0 Main page])
     110----
     111'' How do I install an Atemio 7600 IRD image? ''
     112 * Visit the Atemio homepage or the AAF digital forum and download the latest TitanNit firmware . ([#point8.15 IRD Download Locations])
     113 * Extract the zip file
     114 * Now copy the unzipped IRD firmware file to a formatted FAT32 USB stick.
     115     Note: The USB stick should not be formatted with windows. Use a separate program, such as the
     116     " HP USB Disk Storage Format Tool" (freeware program).
     117     Furthermore, we recommend a cheap USB stick with a small storage capacity as well as read and write speed.
     118 * Turn off the Receiver and disconnect all USB devices.
     119 * Connect the USB stick with the IRD file to your Receiver
     120 * Switch on (mains switch) and at the same time hold the CH + on the unit (about 15 seconds) until "search IRD File ... " appears,
     121   and the installation begins. Only then release the button
     122     Note: If installation does not start , use a different USB stick.
     123 * After successfully installing the receiver will reboot and the installed image should start-up
     124[[br]]
     125  '''[wiki:Remote-Device-Control#point4.6 4.6 Bootloader sh4 Boxen]'''[[br]]
     126* [http://sbnc.dyndns.tv/trac/wiki/en/Remote-Device-Control#point4.6  iboot sh4 loader flashing and recovery ][[br]] 
     127[#point8 Top of Page]
     128[[br]]
     129----
     130'''8.6 Atevio7000 and Fortis FS-9000/9200''' [=#point8.006] ([wiki:Wiki#point0 Contents]) ([WikiStart#point0 Main page])
     131----
     132'' How do I install an Atemio 7000 IRD image? ''
     133 * Visit the Atemio homepage or the AAF digital forum and download the latest TitanNit firmware . ([#point8.15 IRD Download Locations])
     134 * Extract the zip file
     135 * Now copy the unzipped IRD firmware file to a formatted FAT32 USB stick.
     136     Note: The USB stick should not be formatted with windows. Use a separate program, such as the
     137     " HP USB Disk Storage Format Tool" (freeware program).
     138     Furthermore, we recommend a cheap USB stick with a small storage capacity as well as read and write speed.
     139 * Turn off the Receiver and disconnect all USB devices.
     140 * Connect the USB stick with the IRD file to your Receiver
     141 * Switch on (mains switch) and at the same time hold the CH + on the unit (about 15 seconds) until "search IRD File ... " appears,
     142   and the installation begins. Only then release the button
     143     Note: If installation does not start , use a different USB stick.
     144 * After successfully installing the receiver will reboot and the installed image should start-up
     145[[br]]
     146  '''[wiki:Remote-Device-Control#point4.6 4.6 Bootloader sh4 Boxen]'''[[br]]
     147* [http://sbnc.dyndns.tv/trac/wiki/en/Remote-Device-Control#point4.6  iboot sh4 loader flashing and recovery ][[br]] 
     148[#point8 Top of Page]
     149[[br]]
     150
     151----
     152'''8.007 Uninstalling Titan''' [=#point8.007] ([wiki:Wiki#point0 Contents]) ([WikiStart#point0 Main page])
     153----
     154If you have an Atemio (Atevio) receiver all you have to do is install your original ird file as explained above and no bootloader changes are neccessary.
     155
     156
     157[[br]]
     158[#point8 Top of Page]
     159[[br]]
     160
     161----   
     162'''8.008 Update TitanNit''' [=#point8.008] ([wiki:Wiki#point0 Contents]) ([WikiStart#point0 Main Page]) 
     163----
     164There are two ways to update your TitanNit version and there are merits to both methods :
     165
     166IRD offline method see above [#point8.00 SH4 Atemio contents] and select your Reciever model to show information on how to update titan using an IRD titannit image.
     167[[br]]
     168''Note: using this method plugins and files stored to Flash will be formatted when the update is proformed.
     169Plugins and files installed to MNT (except on the ufs 910/922) or a valid configured storage device will retain there settings .''
     170
     171Image Online Method see [wiki:System-Update#point3.5.7 System update] for information on how preform an online update.
     172[[br]]
     173''Note: using this method all plugins and settings are retained as long as they are not installed in flash.''
     174[[br]]
     175[#point8 Top of Page]
     176[[br]]
     177
     178----   
     179'''8.009 IRD Download Locations''' [=#point8.009] ([wiki:Wiki#point0 Contents]) ([WikiStart#point0 Main Page]) 
     180----
     181* [wiki:Manufactures#point13 13 Manufactures] - [http://atemio.de/index.php/software-updates Stable Images][[br]] 
     182* [wiki:Community#point14 14 Community] - [http://www.aaf-digital.info/forum/downloads.php?do=cat&id=2 Stable Images] [http://www.aaf-digital.info/forum/pages.php?pageid=12 Nightly Images][[br]] 
     183 
     184[[br]] 
     185[#point8 Top of Page] 
     186[[br]]
Note: See TracChangeset for help on using the changeset viewer.